Orbis CALORAMA Installation And Operating Manual Download Page 2

1

CALORAMA/COMFORT VIEW SERIES DIRECT VENT WALL FURNACE

INSTALLATION AND OPERATING MANUAL

SECTION I  -  Introduction and Safety Information
Introduction
Basic Description
Qualified Service Agency
Safety Rules
Safety Information for Users of Propane / L.P. Gas
Propane / L.P. Gas odor Warning
CALORAMA/COMFORT VIEW (CCV) HEATER SPECIFICATIONS

SECTION II  –  Installing Your Orbis ( CCV ) Direct Vent Space Heater
Unpack the Heater
Locating the Orbis Calorama/Comfort View Series Space Heaters

Figure 1: Outside Clearances to the Vent Cap             
Figure 2: Clearances for Mounting the Heater Itself
Table 2: Minimum Clearances Required for Mounting

Mounting Template

Figure 3: ALL MODELS – Unit Mounting Instructions
Figure 4: Unit Mounting Template Position
Figure 5: Wall Mounting Plate

SECTION III  -  Vent, Wall Plate and Unit Installation
Unpack the Vent Assembly
Prepare for Installation

Figure 6: Exploded Side View of Vent Installation

Vent and Wall Plate Installation

Figure 7: Vent Kit Assembly                   
Figure 8: Vent Cap as seen from the Outside

Connect Gas Piping
Gas Supply
Pressure Testing of the Gas Supply Piping System

Figure 9: Guidelines for Gas Piping Connections 

Check for Gas Leaks
Installing the Unit Cover
Lighting the Unit

Figure 10: Lighting Instructions

Adjusting the Thermostat

SECTION IV  -  Maintenance Instructions
Maintenance Instructions (General)
Maintenance Instructions for Calorama/Comfort View Series Heaters

Figure 11: Flame Pattern Calorama/Comfort View Series

SECTION V  -  Troubleshooting Guide
SECTION VI  -  Replacement Parts Guide
SECTION VII  - Limited Warranty
SECTION VIII  -  Blower Option

  

         

INDEX

Page 2
Page 2
Page 2
Page 3
Page 4
Page 5
Page 5

Page 6
Page 6
Page 7
Page 8
Page 8
Page 8
Page 9

Page 10
Page 10

Page 11
Page 11
Page 11
Page 12
Page 13
Page 13
Page 14
Page 14
Page 14
Page 15
Page 15
Page 16
Page 16
Page 16
Page 17

Page 18

Pages 18-20

Page 20

Pages 21-23
Pages 24-25
Pages 26-27
Pages 28-29

Summary of Contents for CALORAMA































Reviews: