Oracle Sun Server X4-4 Installation Manual Download

Page: 140 / 148

Reset the Server

The server powers down completely.

See Also

■

“Use the Power Button for Immediate Shutdown” on page 138

■

“Use the Oracle ILOM CLI for Immediate Shutdown” on page 139

Reset the Server

Use the procedures in one of the following sections to reset the server.

Caution -

Possible data loss. Resetting the server will cause any unsaved data on the server to

be lost.

■

“Use the Oracle ILOM CLI to Reset the Server” on page 140

■

“Use the Oracle ILOM Web Interface to Reset the Server” on page 140

Use the Oracle ILOM CLI to Reset the Server

Log in to the Oracle ILOM command-line interface (CLI) using an Administrator

account.

Oracle ILOM displays the default command prompt (->), indicating that you have successfully

logged in to Oracle ILOM.

From the CLI prompt, type the following command:

reset /System

The server resets.

See Also

■

“Use the Oracle ILOM Web Interface to Reset the Server” on page 140

Use the Oracle ILOM Web Interface to Reset the

Server

Log in to the Oracle ILOM web interface using an Administrator account.

The Oracle ILOM web interface System Information > Summary page appears.

140

Sun Server X4-4 Installation Guide • October 2015

Summary of Contents for Sun Server X4-4





















































































































































Search results

Summary of Contents for Sun Server X4-4

Reviews:

Related manuals for Sun Server X4-4

Brands by name

Popular brands

Oracle Sun Server X4-4, Installation Manual

Search results

Summary of Contents for Sun Server X4-4

Reviews:

Related manuals for Sun Server X4-4

Brands by name

Popular brands