Oracle Sun Server X4-4 Installation Manual Download

Page: 139 / 148

Use the Oracle ILOM CLI for Immediate Shutdown

The server powers down completely.

See Also

■

“Use the Oracle ILOM CLI for Immediate Shutdown” on page 139

■

“Use the Oracle ILOM Web Interface for Immediate Shutdown” on page 139

Use the Oracle ILOM CLI for Immediate Shutdown

Log in to the Oracle ILOM command-line interface (CLI) using an Administrator

account.

Oracle ILOM displays the default command prompt (->), indicating that you have successfully

logged in to Oracle ILOM.

From the CLI prompt, type the following command:

stop -f /System

The server immediately powers down to standby power mode.

To completely power off the server from standby power mode, disconnect the

power cables from the server.

The server powers down completely.

See Also

■

“Use the Power Button for Immediate Shutdown” on page 138

■

“Use the Oracle ILOM Web Interface for Immediate Shutdown” on page 139

Use the Oracle ILOM Web Interface for Immediate

Shutdown

Log in to the Oracle ILOM web interface using an Administrator account.

The Oracle ILOM web interface System Information > Summary page appears.

In the left pane, click Host Management > Power Control, and select Immediate

Power Off from the Select Action list box.

Click Save, and then click OK.

The server immediately powers down to standby power mode.

To completely power off the server from standby power mode, disconnect the

power cables from the server.

Controlling System Power and Viewing BIOS Messages

139

Summary of Contents for Sun Server X4-4





















































































































































Search results

Summary of Contents for Sun Server X4-4

Reviews:

Related manuals for Sun Server X4-4

Brands by name

Popular brands

Oracle Sun Server X4-4, Installation Manual

Search results

Summary of Contents for Sun Server X4-4

Reviews:

Related manuals for Sun Server X4-4

Brands by name

Popular brands