Oracle Sun Netra X4270 Service Manual Download Page 137

Page: 137 / 238

Identify and Remove Faulty DIMMs

■

“DIMM Population Rules” on page 134

■

“DIMM Considerations and Limitations” on page 135

■

“DIMM Rank Classification Labels” on page 136

■

“Identify and Remove Faulty DIMMs” on page 137

■

“Install DIMMs” on page 141

Identify and Remove Faulty DIMMs

Prepare the server for service.

See

“Preparing the Server for Component Replacement” on page 75

If there are full-length PCIe2 cards installed in PCIe slots 4 and 5, remove the PCI

mezzanine, if necessary.

See

“Remove the PCI Mezzanine” on page 102

Remove the air duct.

See

“Remove the Air Duct” on page 127

When removing DIMMs from slots D4 through D8 next to CPU P0, remove the

media bay assembly.

See

“Remove the Media Bay Assembly” on page 93

Replacing Motherboard Assembly Components

137

Summary of Contents for Sun Netra X4270















































































































































































































































Search results

Summary of Contents for Sun Netra X4270

Reviews:

Brands by name

Popular brands

Oracle Sun Netra X4270, Service Manual

Search results

Summary of Contents for Sun Netra X4270

Reviews:

Brands by name

Popular brands