manualshive.com logo in svg

Oracle Sun Netra X4270, Service Manual

Share
Download
Oracle Sun Netra X4270 Service Manual Download Page 136

Replacing DIMMs

DIMM Rank Classification Labels

DIMMs come in a variety of ranks: single, dual, or quad. Each DIMM is shipped with a

label identifying its rank classification. The following table identifies the corresponding rank

classification label shipped with each DIMM.

TABLE 7

DIMM Classification Labels

Rank Classification

Label

Quad-rank DIMM

4Rx4

Dual-rank DIMM

2Rx4

Single-rank DIMM

1Rx4

Related Information

■

“DIMM and CPU Physical Layout” on page 133

■

“DIMM Considerations and Limitations” on page 135

■

“Error Correction and Parity” on page 136

■

“Identify and Remove Faulty DIMMs” on page 137

■

“Install DIMMs” on page 141

Error Correction and Parity

The server???s processor provides parity protection on its internal cache memories and ECC

protection of the data. The system can detect and log these types of errors to the ILOM event

log:

■

Correctable and uncorrectable memory ECC errors

■

Uncorrectable CPU internal errors

Advanced ECC corrects up to 4-bits in error on nibble boundaries, as long as al l of these bits

are all in the same DRAM. If a DRAM fails, the DIMM continues to function.

For instructions for clearing DIMM faults, see 

“Install DIMMs” on page 141

. For more

information about fault management, refer to the ILOM 3.0 documentation.

Related Information

■

“DIMM and CPU Physical Layout” on page 133

136

Sun Netra X4270 Server • September 2015

Summary of Contents for Sun Netra X4270















































































































































































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands