Oracle Netra SPARC S7-2 Service Manual Download

Page: 46 / 258

Service Tools

■

ESD mat

■

Antistatic bag used to wrap a replacement part, if turned inside out after removing the part

and

placed on an antistatic surface

■

A disposable ESD mat (shipped with some replacement parts or optional system

components)

Related Information

■

“Service Tools” on page 46

■

“Component Service Task Reference” on page 47

■

“Removing Power From a Server” on page 49

Service Tools

You need these tools for most service operations:

■

Antistatic wrist strap

■

Antistatic mat

■

Small flat head screwdriver

■

No. 1 Phillips screwdriver

■

No. 2 Phillips screwdriver

Related Information

■

“Safety Information” on page 44

■

“Component Service Task Reference” on page 47

■

“Accessing Internal Components” on page 55

Fillers

Servers might be shipped with replacement fillers for hard drives and PCI cards. A filler is an

empty metal or plastic enclosure that does not contain any functioning system hardware or cable

connectors.

The fillers are installed at the factory and must remain in the server until you replace them with

a functional component to ensure proper airflow through the system. If you remove a filler and

Netra SPARC S7-2 Server Service Manual • February 2017

Summary of Contents for Netra SPARC S7-2



































































































































































































































































Search results

Summary of Contents for Netra SPARC S7-2

Reviews:

Related manuals for Netra SPARC S7-2

Brands by name

Popular brands

Oracle Netra SPARC S7-2, Service Manual

Search results

Summary of Contents for Netra SPARC S7-2

Reviews:

Related manuals for Netra SPARC S7-2

Brands by name

Popular brands