Oracle EXADATA X6-2 Installation Manual Download

Page: 71 / 72

Index

agency compliance specifications, 18

cable management arm (CMA)

installing on storage server, 40

uninstalling, 55

verifying operation, 53

cabling, required cable connections, 61

environmental specifications, 16

Ethernet ports, 62

installing storage server

spares kit components, 13

installing storage server into a rack, 25

installing storage server, tools required, 27

mounting brackets, installing, 30

network management (NET MGT) port, location

of, 62

physical specifications, 15

rack installation, 25

rackmount

kit, 25

rail assembly, 25

stabilizing the rack, 29, 49, 53, 55

rail assembly, 25

serial management (SER MGT) port, 62

shipping cartons

checking for damage, 13

shipping cartons contents, 13

slide-rails

verifying operation, 53

spares kit components, installing, 13

specifications

agency compliance, 18

physical, 15

support worksheet, 68

tool-less slide-rail assemblies, installing, 35

USB ports, 62

Summary of Contents for EXADATA X6-2









































































Search results

Summary of Contents for EXADATA X6-2

Reviews:

Related manuals for EXADATA X6-2

Brands by name

Popular brands

Oracle EXADATA X6-2, Installation Manual

Search results

Summary of Contents for EXADATA X6-2

Reviews:

Related manuals for EXADATA X6-2

Brands by name

Popular brands