Oracle EXADATA X6-2 Installation Manual Download

Page: 61 / 72

Cabling the Storage Server

This section contains procedures for connecting data and system management cables and power

cords to the storage server.

Description

Links

Review connector port locations.

“Rear Cable Connections and Ports” on page 61

Learn about storage server Ethernet ports.

“Ethernet Ports” on page 63

Connect power cords to the storage server.

“Connect the Power Cords” on page 63

Related Information

■

“Rack Installation Procedure Overview ” on page 19

Rear Cable Connections and Ports

The following figure shows the locations of cable connectors and ports on the back of the

Oracle Exadata Storage Server X6-2 Extreme Flash and the cables and devices that you would

typically connect to them.

Cabling the Storage Server

Summary of Contents for EXADATA X6-2









































































Search results

Summary of Contents for EXADATA X6-2

Reviews:

Related manuals for EXADATA X6-2

Brands by name

Popular brands

Oracle EXADATA X6-2, Installation Manual

Search results

Summary of Contents for EXADATA X6-2

Reviews:

Related manuals for EXADATA X6-2

Brands by name

Popular brands