Optronis CoaXPress CamPerform Cyclone Series User Manual Download Page 6

Page: 6 / 35

-6-

General

1.1

RoHS Compliance

CamPerform Cyclone-5-700-M/C cameras are Pb free manufactured.

1.2

Standards

The camera has been developed according to following standards:

•

CoaXPress Standard Version 2.0 - JIIA CXP-001-2019

1.3

Remarks

The following signs are used in this user manual to highlight some information:

Remarks and additional information.

Attention, warnings.

1.4

Scope of Delivery

The camera is delivered together with:

•

Brief Introduction

Available accessories are:

•

CY-CM

C-Mount lens adapter

•

CY-FM

F-Mount lens adapter

•

CY-M42

M42 Mount lens adapter

•

CPH6-PTC

Pig tail cable for synch

•

CPH6-USB

Programming Cable

•

CY-HIS

Heat Sink

•

CY-FAN

Cooling Fan

Summary of Contents for CoaXPress CamPerform Cyclone Series




































Search results

Summary of Contents for CoaXPress CamPerform Cyclone Series

Reviews:

Related manuals for CoaXPress CamPerform Cyclone Series

Brands by name

Popular brands

Optronis CoaXPress CamPerform Cyclone Series, User Manual

Search results

Summary of Contents for CoaXPress CamPerform Cyclone Series

Reviews:

Related manuals for CoaXPress CamPerform Cyclone Series

Brands by name

Popular brands