background image

Page  6

This microscope is a scientific precision instrument designed to last for many years with a minimum of main

-

tenance. It is built to high optical and mechanical standards and to withstand daily laboratory use.
Optika reminds you that this manual contains important information on safety and maintenance, and that it 
must therefore be made accessible to the instrument users.
Optika declines any responsibility deriving from instrument use that does not comply with this manual.

3.0 UNPACKING AND ASSEMBLY

2.0 INTRODUCTION

3.1

  

The microscope is housed in a moulded Styrofoam container. Remove the tape from the edge of the 
container and lift the top half of the container. Take some care to avoid that the optical items (objecti

-

ves and eyepieces) fall out and get damaged. Using both hands (one around the arm and one around 
the base), lift the microscope from the container and put it on a stable desk.

3.2

   The objectives are located in individual protective vials. Remove the objectives from the vials and 

insert them into the microscope nosepiece in the order from the lowest magnification to the highest, in 
a clockwise direction from the rear. 

3.3

 

Insert the analyzer/bertrand lens block onto the top of the microscope stand and lock its screw:

Summary of Contents for B-500POL

















Reviews: