Optics OMM-1000 Page 30 User Manual Download | Manualshive

Page: 30 / 49

background image

30

6.2.3 Network setting

▪

It sets IP, Gateway, Subnet mask, MAC address and UDP port number.

▪

It requests current network setting.

Command

Description and reply

NETGW=192.168.1.1!

Sets Gateway address, each data ranges from 000 to 255.
Reply: NETGW=192.168.001.001!

NETIP=192.168.1.118!

Sets IP address, each data ranges from 000 to 255.
Reply: NETGW=192.168.001.118!

NETSN=255.255.255.0!

Sets Subnet mask address, each data ranges from 000 to 255.
Reply: NETSN=255.255.255.000!

NETPA=AA.BB.CC.DD.EE.FF!

Sets MAC address, each data ranges from 00 to FF.
Reply: NETPA= AA.BB.CC.DD.EE.FF!

NETPT=3000!

Sets UDP port number, data ranges from 0 to 65535.
NETPT=3000!

NET=?!

Requests current network setting.
Reply: NETGW=192.168.001.001!

NETIP=192.168.001.118!
NETSN=255.255.255.000!
NETPA=AA.BB.CC.DD.EE.FF!
NETPT=3000!

Table 6.4 Network setting command examples

6.2.4 Video generator setting

▪

It changes resolution and pattern of video generator.

▪

It requests current video generator setting.

Table 6.5 describes the resolutions and patterns OMM-1000 supports. By command input
operation, user can change these to be used with on-site source for easy installation

Data #

Resolution

Pattern

1

800x600@60Hz

Vertical Color Bar

2

1024x768@60Hz

Vertical Color Bar scroll (Interval:0.5sec)

3

1280x960@60Hz

Vertical Color Bar scroll (Interval:1.0sec)

4

1280x1024@60Hz

Horizontal Color Bar

5

1600x1200@60Hz

Horizontal Color Bar scroll (Interval:0.5sec)

«
...
28
29
30
31
32
...
»

Summary of Contents for OMM-1000


















































Reviews:

No comments

Related manuals for OMM-1000

Brand: Takstar Pages: 2

PowerLight PL325

Brand: QSC Pages: 12

Brand: imaage dynamics Pages: 9

Brand: Miranda Pages: 4

Brand: Bazooka Pages: 32

Brand: Technics Pages: 100

Brand: Harman Kardon Pages: 8

Brand: Nady Audio Pages: 2

Reference 750 SE

Brand: Audio Research Pages: 18

Brand: FMS Pages: 24

Brand: Xicom Pages: 36

Brand: HEED Pages: 2

ONYX ONX1.1000D

Brand: MB QUART Pages: 12

Brand: MAG THEATRON Pages: 28

Brand: Marantz Pages: 86

Apocalypse AP600.2

Brand: Planet Audio Pages: 21

Brand: Sams Pages: 18

Brand: Gamut Pages: 10

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands