Optics OMM-1000 Page 17 User Manual Download | Manualshive

Page: 17 / 49

background image

17

3.3.11 Control Lock: Press FUNCTION key button eleven times

▪

It locks and unlocks the controls such as Web, RS-232, TCP/IP, UDP and key button

====Control Lock====

Web Lock? UnLock

Data Lock? UnLock

Key Lock? UnLock

▪

Input 1 and 2 key buttons move the cursor up and down.

▪

Input 3 key button moves Lock.

▪

Input 4 key button moves UnLock.

▪

Press ENTER key button to complete the process.

3.3.12 Reset Mode: Press FUNCTION key button twelve times

▪

It resets OMM-1000. It starts rebooting and restores all default setting.

▪

Press Input 1 key button to complete the process.

«
...
15
16
17
18
19
...
»

Summary of Contents for OMM-1000


















































Reviews:

No comments

Related manuals for OMM-1000

Brand: NAD Pages: 36

Brand: NAD Pages: 3

Brand: Samson Pages: 16

Brand: Accel Instruments Pages: 2

Brand: Bazooka Pages: 32

Brand: Peavey Pages: 15

HD-AMP1/U1B/K1B/FN

Brand: Marantz Pages: 99

Brand: Harman Pages: 21

Brand: Nakamichi Pages: 16

Okur A7 Series A71100.1

Brand: DB Drive Pages: 12

Brand: Crest Audio Pages: 2

Brand: MadBoy Pages: 7

Brand: AudioControl Pages: 12

Brand: Marantz Pages: 81

Brand: IMG STAGELINE Pages: 13

Brand: Cyrus Pages: 20

Brand: Yaesu Pages: 10

Brand: Qtx Pages: 4

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands