manualshive.com logo in svg

Opticon OPL 2724 ZAPPER, Specification Manual, Page: 10 / 27

Share
Download
Opticon OPL 2724 ZAPPER Specification Manual Download Page 10

Opticon 

OPL 2724 

Specifications Manual 

 
 
 
 

 

10 

6.5. Operating Indicators 

The OPL 2724 displays its operating state with LEDs and a buzzer. 

Action 

Indicator / Buzzer 

Description 

Start-up beep 

6 short beeps (low, medium, high, 
low, medium, high) 

Battery is placed in OPL 2724 (start-up buzzer) 

Blue LED is flashing 

OPL 2724 is attempting to establish a 
Bluetooth connection 

Blue LED is flashing slow 

OPL 2724 is connectable (as slave) 

Blue LED on and high sound for 1 
second 

Bluetooth connection was (re)established 

 
 
 
Connecting /  
Connectable 

When pressing trigger: High-low 
sound of 0.2 seconds followed by the 
blue or red LED flashing. 

The user has pressed the trigger long enough 
to create or break the connection. After the 
signals, the user can release the trigger key. 

Red LED on with low sound for 1 
second 

Connection attempt failed 
Connection loss is detected 
During ‘Auto reconnect time’ every 15 or 30 
seconds (depending on connection type) 

Red LED is flashing 

OPL 2724 is disconnecting a Bluetooth 
connection 

 
 
Disconnecting /  
Connection 
failure 
Connection 
lost 
 

Red LED on and a long high-low 
sound for 1.6 seconds 

OPL 2724 successfully disconnected the 
Bluetooth connection 

Green LED and beep as configured in 
the Universal Menu Book at Chapter 
6.1. and 6.2 

Valid barcode label read with an active 
Bluetooth connection 

Short green LED and beep of half the 
length as configured in the Universal 
Menu Book at Chapter 6.1 and 6.2 

Valid barcode label read and stored in memory 
(data is not transmitted; i.e., because there is 
no active Bluetooth connection 

Orange LED as configured in the 
Universal Menu Book at Chapter 6.2 
with low sound 

Valid barcode label read with no active 
Bluetooth connection 

 
 
 
 
Barcode 
reading 
 

Short click sound 

Partial read beep of (Micro)PDF417 decoder 

High-low sound with LED: 
Green (Misc.) / Red (Disconnect) / 
Blue (Connect) 

Valid Bluetooth action label read (i.e., connect / 
disconnect / unpair ) 

Orange LED on and low sound of 0.2 
seconds 

Bluetooth action label read that could not be 
executed because OPL 2724 was already 
(dis)connected 

 
 
Action / 
configuration  
label reading 

Slow beeping sound 

Menu book configuration mode 

Very slow blinking red LED 

Low battery indicator 

 
Miscellaneous  

Green LED flashes and 8 high short 
beeps 

Error correction busy of (Micro)PDF417 data 
with a high error correction level 

Buzzer 

Loudness: 70 dBA or higher (when 
the scanner is set to “Loud”) 

Buzzer loudness was estimated at a point 10 
cm behind the scanner. 

Summary of Contents for OPL 2724 ZAPPER




























Reviews:

No comments