background image

 

OPTICAL SYSTEMS DESIGN 

 

DOC ID: 10110306 

OSD8826 OPERATOR MANUAL

 

 

PAGE 8 

 

2

 

INSTALLATION AND OPERATION 

2.1

 

INTRODUCTION 

This  section  outlines  the  methods  required  to  install  and  operate  the  OSD8826T  and  OSD8826R 
successfully. It should be studied carefully if damage to the equipment or poor results are to be avoided. 

This equipment has been fully tested prior to dispatch and is ready for immediate operation.  However it 
is advisable to check for external transportation damage before operation. If damage is evident, return 
the unit with the packaging to your supplier immediately. 

2.2

 

INSTALLATION 

2.2.1

 

WARNING AND PRECAUTIONS 

▲ 

ELECTROMAGNETIC COMPATIBILITY 

WARNING

: This is a Class A product. In a domestic environment this product may cause radio 

interference in which case the user may be required to take adequate measures. 
 

▲ 

OPTICAL OUTPUT OPERATION

 

WARNING

Laser Safety:

 Class 1 Laser Product per IEC/EN 60825-1:20011 standard. 

 

Class 1 

The OSD8826 is a 

Class 1

 

laser product.

 

 

 

PRECAUTIONS 

 

▲ 

All service personnel should be provided training as to the hazards of direct viewing of laser 
radiation and of the precautionary measures during servicing of equipment 

▲ 

Areas  where  laser  products  are  installed  should  be  restricted  in  access  to  trained  service 
personnel only and appropriate warning signs posted in the work area. 

▲ 

All  laser  apertures  should  be  covered  by  protective  covers  when  not  connected  to  optical 
fibers. Never leave outputs uncovered. 

▲ 

Laser  equipment  should  be  positioned  above  or  below  eye  level  where  possible.  Apertures 
should be positioned away from personnel. 

▲ 

Protective eyewear should be worn in the vicinity of laser equipment.

 

Summary of Contents for OSD8826 Series





















Reviews: