background image

13

Instructions

12

Please consider when you
inscribe the data side:

As data burning starts at the
innermost area of the disc it is
recommended  that you finish
data burning prior to inscription.
If there is then sufficient space
available for an inscription (outer
area) you can perform the marking.

Please find below a diagram
showing the relation on burned
data and outer radius of the data
area (single session):

Please keep in mind that the min.
width for an inscription is 5mm!

After the labelling is completed
the tray of the drive opens
automatically and the inscribed
media can be removed.
By selecting „Cancel“  you will
go back to the NeroExpress start
menu.

Technical Data

Inner radius:

min. 25mm - max. 53mm

Outer radius:

min. 28mm - max. 58mm

Width of the label area:

min. 5mm - max. 33mm

Disc rotation speed:

7875rpm, 4500rpm, 2250rpm

(depends on the selected media)

Resolution/gradation:

1000dpi/256

Above specifications

are subject to change.

Labelflash™ is a trademark of

Yamaha used under license.

How to create a Label with Nero

To create a Labelflash™ inscription
you have to first start NeroExpress.

Then please click the left side
of the Window the button:

To start the Labelflash™ design
and burn application you have to
continue by selecting                    .

The usage of this application is
the same as the „Nero CoverDesigner“
– please study its instructions if
you need more details.

Once the Labelflash™ media
(„PRINTING SIDE“ down),  or a data
side of a DVD +/-R (data side down),
has been placed in the drive the
application will show the corres-
ponding disc type – after which the
„burn“      button can be selected.

Summary of Contents for CD-1100













Reviews: