Optex VX-402 Instalation Instructions Download Page 12

7-2.Day/Night Message Mode 

(VX-402REC only)

7-3.Arm/Disarm Mode 

(VX-402REC only)

7-4.Sequential Message Mode 

(VX-402REC only)

-12-

In case, the detector detects the moving object 3 times within 30 seconds during the Sequential
Message mode is set ON, the message is automatically changed from 3

rd

 time detection.

     1

st

 and 2

nd

 time detection (within 30 seconds) : Message A

     3

rd

 time detection (within 30 seconds)             : Message B

The detector will automatically change messages from that for the daytime to that for the night-time and
vice versa.

         Daytime   : Message A
         Night-time: Message B

The detector will sound different messages when it is set for the armed mode or disarmed mode.
     Armed     : Message A
     Disarmed: Message B

Caution!

(Message A)

Warning!

(Message B)

Caution!

(Message A)

Warning!

(Message B)

ARMED

Control Panel

DISARMED

Control Panel

Non-Voltage Contact Control

Voltage Control

Non-Voltage Contact Control

Voltage Control

OPEN  DC 5 - 18V       CLOSE    DC 0 -  1V

CLOSE DC 0 -  1V       OPEN      DC 5 - 18V

+ARM –ARM

Armed

Disarmed

Detector Setting

Control Panel

Non-Voltage Contact Control

Voltage Control

Wiring between Power(–)and Voice Contorol Input

Wiring to PGM Programmable Output

Control Panel

Non-Voltage Contact Output

Control Panel

PGM Output

Caution!

(Message A)

Warning!

(Message B)

Voice Mode Switch

Voice Mode Switch

Voice Mode Switch

Power(–)

Voice Contorol Input

Voice Contorol Input

123

4

123

4

123

4

alarm shop

Summary of Contents for VX-402

















Reviews: