- 2 -
INSTALLATION
3
Caution
3-1 SEPARATING
1
• Do not place the main
unit where it is exposed
to direct sunlight. Doing
so may cause damage to
the product.
4
Remove the main unit from the back box.
5
Remove the main unit mounting bracket.
Remove the battery
cover.
2
Remove the main unit
cover.
3-2 WALL MOUNTING
1
Using a screwdriver or similar tool, break
the knockout position (×2) in the back
box as shown.
2
3
6
Insert/replace batteries.
Disposal method for batteries
Note>>
Using Velcro tape, fix the wireless
transmitters in the back box.
For more information on wiring,
see “3-5 WIRING” on page 3.
5
Attach the connectors.
• When using BCU-4 (option), refer to
BCU-4 manual.
4
Mount the main unit.
7
Referring to “4 SETTING” on page 3,
perform the necessary settings.
8
Close the main unit cover.
Warning
• When closing the cover, be careful that
the cables are not caught by the cover.
Caution
9
Close the battery cover.
Caution
• Do not touch the optical unit
when mounting the cover.
Otherwise, the resulting shift
of the optical axis may result
in malfunction of the unit and
require readjustment.
3
Remove the connectors.
Pull
2
Pull
2
Loosen the
battery cover
lock screw.
1
Loosen the
main unit cover
lock screw.
1
Velcro tape
Cut the supplied Velcro
tape to an appropriate
length and apply.
3-3 POLE MOUNTING
1
Using the guide below, break the knockout positions (×2) in the back box with a screwdriver.
3
Perform the wall
mounting procedure of
3 to 9 on page 2.
One detector
Two detectors in
opposing directions
Knockout position
Detector No. 1 Detector No. 2
Instruction
condition
POLE (1)
-
POLE (1)
POLE (2)
Caution
• If you accidentally open an
unnecessary knockout, be sure
to fill the knockout. Not doing so
may result in waterproof failure
and malfunction of the product.
Insert the two batteries into their
compartment. Ensure the positive
terminals are facing toward the front.
2
Close the battery plate.
3
Connect the CRH-5 male connectors
to the female connectors of the
battery plate.
4
1 Open the battery plate in the
direction of the arrow.
Set CR123A in the CRH-5 and insert
two CRH-5 into their compartment.
Ensure the positive terminals are
facing toward the front.
2
Close the battery plate.
3
1 Open the battery plate in the
direction of the arrow.
< When using D size battery >
< When using CR123A battery >
Mount the back box to the wall.
• Do not mix D size lithium batteries with CRH-5 batteries.
• Do not mix batteries that have different levels of power remaining (i.e., new
and used batteries or batteries of different manufacturers). Not observing
the above may result in an explosion, leakage of electrolyte, emission of
toxic gases or other outcomes that may be harmful to people and property.
Caution
• Remove all batteries prior to replacing with new ones. If this is not followed,
the low battery indicator LED will not reset and will continue to blink.
Open the screw holes from the
inside of the back box to the
outside.
Open the screw holes from the inside
of the back box to the outside.
Dispose of used batteries in accordance with local
government regulations/low and EU Battery
Directive (2006/66/EU).
Take the main unit out
of the back box.
2
1
3
Turn the optical unit
90 degrees and
loosen the screw.
1
2
Tighten the main unit fixing
screw and turn the optical unit
90 degrees.
3
1 Attach the main unit
mounting bracket to the back
box.
2 Route the three connectors
of the back box through the
slits on the upper part of the
main unit.
1
3
4
Tighten the fixing screw for the battery cover.
2
2
Close the battery cover.
1
Knockout position
WALL
POLE (1)
POLE (2)
Knockout position
WALL
POLE (1)
POLE (2)
4×20 self tapping
(with rubber washer)
Side wall
Distance from
the side wall:
at least 1m
Pitch: 83.5 mm
For connection
to gang electric
box
1
3
4
2
3.9 VDC D size
Lithium batteries
CRH-5
3.0 VDC CR123A
1
2
3
Hook on the upper part
of the back box.
Push the lower part of
the main unit cover.
Fasten the main unit
cover lock screw.
2
1
3
2
Fix the back box on the pole.
Side wall
M4×20 screw
(with rubber washer)
Pole bracket
U-bracket
Distance from the side
wall: at least 1m
Pole 43 to 48 mm dia.
(1.69 to 1.89 inch dia.)
Detector
No. 1
Detector
No. 2
Just fit
Note>>
• Avoid placing the cables
in a position where they
can be caught between
the main unit and cover.
