background image

FCC notification

This equipment has been tested and found to comply with the limits for a Class A digital device, 
pursuant to part 15 of the FCC Rules. These limits are designed to provide reasonable protection 
against harmful interference when the equipment is operated in a commercial environment.
This equipment generates, uses, and can radiate radio frequency energy and, if not installed and 
used in accordance with the instruction manual, may cause harmful interference to radio 
communications. Operation of this equipment in a residential area is likely to cause harmful 
interference in which case the user will be required to correct the interference at his own expense.

Personal Information

This product is equipped with the function to produce moving image of the designated area and 
its surrounding, but not equipped with the function to store or register such image.
Prior to the installation of this product, the compliance to local laws and regulations needs to be 
confirmed by the user of this product for the lawful installation and use of this product, and signage 
and notification when using this product.  User of this product is deemed to be responsible for the 
compliance of any laws and regulations relating to personal information, privacy protection and 
rights of portrait upon use of this product.  Image taken by this product is required to be treated 
appropriately under the responsibility of the user of this product.
Installation of this product, producing image, monitoring, recording with camera and handling of 
personal information or data shall all be performed under discretion and responsibility of user of 
this product, and OPTEX shall not be held liable for any dispute between a user and a third party.

- Compliance

- 15 -

About distribution of source code for open source software

This product includes open source software

” OSS”

 distributed under OSS License. In compliance 

with the OSS Licenses such as GPL (GNU GENERAL PUBLIC LICENSE), LGPL (GNU LESSER-
GENERAL PUBLIC LICENSE), and/or others included, we are making the source code of the OSS 
available, at the actual cost, to our customer upon his/her request. The source code corresponding to 
OSS included in this product will be provided in a prescribed manner for at least than three(3) years 
after the date of purchase. Please note that the OSS is provided without warranty of any kind.

Others

Summary of Contents for InSight INS-QXI-ST

















Reviews: