background image

Preface

Installation

Troubleshooting

Specifications

23

Distribution of source code for open source software

This product includes open source software.
We can copy and distribute the source code of the software according to the license requirements if the open source software includes LGPL (GNU 
LESSERGENERAL PUBLIC LICENSE) or other licenses under the conditions of disclosure.
Regarding the open source code of this product, we will distribute the source code corresponding to the open source software at the actual cost 
for at least 3 years after purchasing it to the individual/group who made the inquiry.

Contact: OPTEX OSS information desk
E-mail: [email protected]

This product contains various open source software to which the following license information applies.

arduino-esp32

GNU Lesser General Public License v2.1

AsyncElegantOTA

MIT License

AsyncTCP

GNU Lesser General Public License v3.0

CRC

MIT License

ESPAsyncWebServer

GNU Lesser General Public License version 2.1

ESPAsyncTCP

GNU Lesser General Public License v3.0

jQuery 3.6.0 min

MIT License

Dimensions

 

„

OA-607 T and loop harness

10 7/8” (276)

1 5/8”

(42)

1 1/2” (38)

1/2” (12.8)

[inch(mm)]

2 1/4” (56.9)

1 5/8”  (41.3)

1 5/16” (33.2)

(12 1/2” (318.25))

 

„

OC-907C T

4 5/8" (117)

1" (25)

2 1/2" (63)

[inch(mm)]

Summary of Contents for ELITE PRO

























Reviews: