background image

19

WARRANTY 

Unless an individual product is covered by a separately issued warranty, Gentex warrants that all ballistic helmet 
shells will be free from defects in material or workmanship under normal use and service for a period of five 
(5) years from the date of delivery. Unless an individual product is covered by a separately issued warranty, 
Gentex warrants that all helmet components, accessories, peripherals, and parts will be free from defects in 
material or workmanship under normal use and service for a period one (1) year from the date of delivery. All 
repair covered by this warranty shall be performed at Gentex’s factory, or other such warranty repair facilities of 
Gentex as designated by Gentex unless Gentex specifically directs that repair services be performed at another 
location. Any defect corrected and found to be within this scope of the warranty will be repaired by Gentex and 
all charges for labor and material will be borne by Gentex. If it is determined that either no fault exists in Gentex, 
or the damage to be repaired was caused by negligence of the user, its agents, employees or customers, you 
agree to pay all charges associated with each such repair. No statement, recommendation or assistance made 
or offered by Gentex through its representatives to the user, its agents, employees, or customers in connection 
with the purpose or intended use of any Gentex’s product shall be or constitute a waiver by Gentex of any of the 
provisions of this warranty or change Gentex’s liability under this warranty.
 
EXCEPT WHERE PROHIBITED BY LAW, THE WARRANTY DESCRIBED ABOVE CONSTITUTES THE SOLE WARRANTY 
MADE BY GENTEX EITHER EXPRESSED OR IMPLIED. THERE ARE NO OTHER WARRANTIES EXPRESSED OR 
IMPLIED THAT EXTEND BEYOND THE FACE HEREOF, HEREIN, INCLUDING THE IMPLIED WARRANTIES OF 
MERCHANTABILITY AND FITNESS FOR A PARTICULAR PURPOSE. IN NO EVENT SHALL GENTEX BE LIABLE FOR 
ANY INCIDENTAL, CONSEQUENTIAL, OR SPECIAL DAMAGES EVEN IF ADVISED OF SUCH DAMAGES, AND THE 
USER, ITS AGENTS, EMPLOYEES, OR CUSTOMERS REMEDIES SHALL BE LIMITED TO SOLELY TO THE REPAIR OR 
REPLACEMENT OF NONCONFORMING UNITS OR PARTS, WHICH AMOUNT SHALL NOT EXCEED THE TOTAL 
PURCHASE PRICE OF THE PRODUCT UNDER WARRANTY.  
 
Any tampering, misuse or negligence in handling or use of the product renders the warranty void. Further, the 
warranty is void if, at any time, the user, its agents, employees or customers attempts to make any internal 
changes to any of the components of a product; if at any time the power supplied to any part of the product 
exceeds the rated tolerance; if any external device attached by the user, its agents, employees or customers 
creates conditions exceeding the tolerance of the product; or if any time the serial number plate is removed or 
defaced. OPERATION OF THE PRODUCTS THAT RENDERS THIS WARRANTY VOID WILL BE DEFINED TO INCLUDE 
ALL OF THE POSSIBILITIES DESCRIBED IN THIS SECTION, TOGETHER WITH ANY PRACTICE THAT RESULTS IN 
CONDITIONS EXCEEDING THE DESIGN TOLERANCE OF THE PRODUCTS.

Summary of Contents for SOTR





















Reviews: