OpenTech Alliance INSOMNIAC CIA K-500 Installation Manual Download Page 11 | Manualshive

Page: 11 / 11

OpenTech Alliance INSOMNIAC CIA K-500 Installation Manual Download Page 11

CIA-575-001 Rev 1.0

11 |

P a g e

KEYPAD MAINTENANCE

Cleaning the Housing and Touchpad

Monthly

:

Inspect and clean the housing and touchpad on a regular basis (monthly) . To clean spray

the unit with a mild soapy water solution then wipe it with a soft cloth. Do not use alcohol, harsh
chemicals, abrasives, or petroleum-based products. Do not immerse the device in water or use a
pressure washer.

Yearly

:

Open the keypad, inspect and clean the inside of the unit. Remove dirt or dust that has collected

on  the  inside  of  the  housing  and  the  circuit  board  that  could  cause  problems.  Note  any  signs  of  water
damage  or  corrosion caused  by a  leak  in  the  enclosure  seals.  Replace  any  worn  seals. A  small  can of
compressed air can be used to remove insects and dust from the circuit board.

NOTICES and DISCLAIMERS

Liability Disclaimer

: While every effort has been made to ensure the accuracy of the information in this document,

and we assume no liability for any inaccuracies contained herein. We reserve the right to change the information
contained herein at any time and without notice.

FCC Part 15 Notice

: This equipment has been tested and found to comply with the limits for a Class B digital device,

pursuant to Part 15 of the FCC Rules. These limits are designed to provide reasonable protection against harmful
interference in a residential installation. This equipment can generate and radiate radio frequency energy and, if not
installed and used in accordance with the instructions, may cause harmful interference to radio communications.

«
...
9
10
11

Summary of Contents for INSOMNIAC CIA K-500












Reviews:

No comments