background image

 

17

 

Playing Your  Components

 

This chapter explains how to use the TX-8011 with your 
other components.

You can use a graphic equalizer by connecting it to the 
TAPE 2 IN/OUT jacks and selecting TAPE 2.

You can adjust the bass, treble, and balance.

You can temporarily mute the TX-8011.

 

To unmute the TX-8011,

 

 press the remote controller’s 

[MUTING] button again. The output is unmuted and the 
AUDIO MUTE indicator goes off.
Muting is cancelled when the TX-8011 is set to Standby.

 

Selecting the Source Component

 

1

 

Press an input selector button to 
select the component that you 
want to play.

 

The name of the selected source 
appears on the display, as shown.

 

2

 

Use the SPEAKERS [A] or [B] 
button to select the speaker set 
that you want to use.

 

The SPEAKERS A and B indicators 
show which speakers are on or off.

 

Note:

 

If both speaker indicators are off, no 
sound will come from speakers.

 

3

 

Start playback on the selected 
component.

 

4

 

To adjust the volume, use the 
VOLUME control, or the remote 
controller’s VOLUME buttons.

Input selector

TAPE 2 MONITOR

SPEAKERS A/B

TUNING

VOLUME

BASS

BALANCE

TREBLE

SPEAKERS  A  B     

A & B speakers indicators

Selected input source

 

Using a Graphic Equalizer

 

1

 

Press the [TAPE 2 MONITOR] but-
ton to select TAPE 2.

 

The T-2 MONITOR indicator lights 
up.

 

2

 

Start playback on the selected 
component.

 

See the graphic equalizer’s manual for 
details.

 

Adjusting the Bass, Treble & Balance

 

Bass

 

You can boost or cut low-frequency 
sounds output by the speakers. Turn 
clockwise to boost; counterclockwise 
to cut.

 

Treble

 

You can boost or cut high-frequency 
sounds output by the speakers. Turn 
clockwise to boost; counterclockwise 
to cut.

 

Balance

 

You can adjust the left and right bal-
ance of the speakers and head-
phones. Turn clockwise to increase the 
output from the right channel; counter-
clockwise to increase the output from 
the left channel.

 

Muting the TX-8011

 

1

 

Press the remote controller’s 
[MUTING] button.

 

The output is muted and the AUDIO 
MUTE indicator flashes on the display, 
as shown.

MUTING

AUDIO MUTE

        

TX-8011̲E.book Page 17 Friday, July 30, 2004 10:33 AM

Summary of Contents for TX-8011

























Reviews: