background image

60

Using remote controller

Controlling an Onkyo CD player

The 

z

 connector of the Onkyo compact disc player must be

connected to the TX-DS787 (see page 13).

1. Press the CD MODE button.

“CD” appears in the remote controller display.

2. Press the desired operation button. The

buttons shaded in the figure to the left are the
operation buttons that can used to control an
Onkyo compact disc player.

TRACK:

 Selects a track

DISC:

 Selects a disk in the CD changer

:

 Track down

:

 Track up

:

 Play

:

 Stop

:

 Fast reverse

:

 Fast forward

:

 Pause

OPEN/CLOSE

 

r

:

 Open/close the disc tray

0, 1 to 9, +10:

 Numeric keys

You may also use the following buttons:

VOL 

:

 Adjusts the volume at the TX-DS787

MUTING:

 Activates the muting function at the TX-DS787

Controlling an Onkyo MD recorder

Make sure that you point the remote controller toward the sensor
on the Onkyo MD recorder.

1. Press the MD MODE button.

“MD” appears in the remote controller display.

2. Press the desired operation button. The

buttons shaded in the figure to the left are the
operation buttons that can used to control an
Onkyo mini disc player.

ON/STNBY:

 Turns the mini disc player on and off

:

 Track down

:

 Track up

:

 Play

:

 Stop

:

 Fast reverse

:

 Fast forward

REC 

o

:

 Record

:

 Pause

r

:

 Eject the disc

1 to 9, +10:

 Numeric keys

ENT:

 Enters the settings

You may also use the following buttons:

VOL 

:

 Adjusts the volume at the TX-DS787

MUTING:

 Activates the muting function at the TX-DS787

OPEN/CLOSE

REC

AUDIO

MUTING

DISC

TRACK

DVD

CD

PH

TUN

T2

T1

V1

STEREO

1

2

3

6

5

4

7

+ 10

0

ENT

8

9

SURROUND

THX

DSP

LEVEL +

CH SEL

Re-EQ

LEVEL –

DIMMER

HOME THEATER CONTROLLER

RC-390M

LATE NIGHT

DIRECT

DSP

V2

V3

V –

CD MODE

OPEN/CLOSE

REC

AUDIO

MUTING

DISC

TRACK

DVD

CD

PH

TUN

T2

T1

V1

STEREO

1

2

3

6

5

4

7

+ 10

0

ENT

8

9

SURROUND

THX

DSP

LEVEL +

CH SEL

Re-EQ

LEVEL –

DIMMER

HOME THEATER CONTROLLER

RC-390M

LATE NIGHT

DIRECT

DSP

V2

V3

V –

MD MODE

ON

STNBY

MD
operation
buttons

Numeric keys,
ENT

CD
operation
buttons

Numeric keys

Summary of Contents for RC-390M













Reviews: