PROGRAMMING FAVORITE CHANNEL SCAN
In the
CBL/SAT
or
TV
mode, you can store a list of up to 10 favorite channels,
in any order, that will be immediately scanned when
FAV
is pressed (see
Using Channel Scan
on the previous page).
NOTE: Favorite channels can only be programmed for one mode.After programming, if
FAV
is pressed while in another mode, the remote control will start scanning all channels instead
(if applicable to the selected device).
1.
On the remote control, press
CBL/SAT
or
TV
once.
2.
Press and hold
SET
until the
LED
(red light) blinks twice,
then release
SET
.
3.
Enter
9
-
9
-
6
. The
LED
will blink twice.
4.
Use the keypad to enter a favorite channel number (e.g.,
031
). Then press
SET
once.
NOTE: If the original remote control required pressing an Enter key
to change the channel, also press the
ENTER
key after the channel
number (e.g.,
0
-
3
-
1
-
ENTER
). On some satellite receivers and cable
boxes, you may need to press the
SELECT
(OK) key instead of
ENTER
.
5.
If desired, repeat step 4 for each channel to be stored, up
to a total of 10 channels.
NOTE: If you try entering more than 10 channels, the remote control
will automatically exit programming. To change your favorite chan-
nel list at this point, you will first need to delete the existing list by
performing the steps in “Clearing Custom Programming”on page 14.
Then, perform the instructions in this section once again.
6.
To exit programming with less than 10 favorite channels
stored, press and hold
SET
until the
LED
blinks twice.
Otherwise, the remote control will automatically exit the
program after 10 channels have been stored.
CHANGING VOLUME LOCK
The One For All 3 Device Universal Remote Control is set at the factory for
independent volume control of each selected device. However, you may
change the Volume Lock setting to Global Volume Lock so that a device’s vol-
ume will be locked to one mode (e.g., to control TV volume in all other
modes).After that, if desired, you can perform Individual Volume Unlock on
a selected device to set its volume control for independent operation.
Locking Volume Control To One Mode
(Global Volume Lock)
1.
Press and hold
SET
until the
LED
(red light) blinks twice,
then release
SET
.
continued on next page...
11
12
PROGRAMMING A MASTER POWER MACRO (cont’d)
Clearing The Master Power Macro
1.
Press and hold
SET
until the
LED
(red light) blinks twice,
then release
SET
.
2.
Enter
9
-
9
-
5
. The
LED
will blink twice. Then press
POWER
once.
3.
Press and hold
SET
until the
LED
blinks twice, then release
SET
. The Master Power Macro is now cleared.
RE-ASSIGNING DEVICE KEYS
The One For All 3 Device Universal Remote Control can be set to control a
DVD player and a VCR (or a PVR) or a second DVD player by re-assigning
the unused
CBL/SAT
key as follows:
1.
On the remote control, press and hold
SET
until the
LED
(red light) blinks twice, then release
SET
.
2.
Enter
9
-
9
-
2
. The
LED
will blink twice.
3.
Press
DVD/VCR
once.
4.
Press
CBL/SAT
once.The
LED
will blink twice.The
CBL/SAT
key
is now ready to be set up to control your VCR (or PVR) or
second DVD player.See Programming Device Control on page
8.
NOTE: Only one device can be assigned to an unused device key at a time.
USING CHANNEL SCAN
In the
CBL/SAT
or
TV
mode, use the
FAV
key to start a 3-second scan of all
channels. Or, if programmed, use the
FAV
key to scan only your favorite
channels to view a desired channel (see Programming Favorite Channel Scan
on next page. )
1.
Press
CBL/SAT
or
TV
once.
2.
Press
FAV
once.
•
If
Favorite Channel Scan
has been set up, scanning of favorite
channels will start with up to 100 channel changes or until
stopped by pressing any key.
•
If
Favorite Channel Scan
has not been set up, scanning
will start with the current channel, and continue up to
100 channel changes or until stopped by pressing any key.
3.
To stop scanning channels at any time, press any key once.
WALRB3P manual booklet 5/2/06 3:13 PM Page 11
Summary of Contents for ONE FOR ALL URC3220
Page 1: ......
