Omron STC-SBS312POE Product Specifications And User'S Manual Download Page 58 | Manualshive

Page: 58 / 62

background image

No.16S019-05

58/62

STC-SBS312POE / STC-SCS312POE / STC-SBS500POE / STC-SCS500POE

Product Specifications and User’s Guide

Name

Description

GevMCDA

Controls the destination IP address for the message channel.

GevMCTT

Provides the transmission timeout value in miliseconds.

GevMCRC

Controls the number of retransmissions allowed when a message channel message time
out.

GevMCSP

This feature indicates the source port for the message channel.

GevStreamChanelSelector

Selects the stream channel to control.

GevSCPDirection

Reports the direction of the stream channel.

GevSCPInterfaceIndex

Index of network interface to use.

GevSCPHostPort

Controls the port of the selected channel to which a GVSP transmitter must send data
stream or the port from which a GVSP receiver may receive data stream.

GevSCPFireTestPacket

Sends a test packet.

GevSCPSDoNotFragment

The state of this feature is copied into the “do not fragment” bit of IP header of each
stream packet.

GevSCPSBigEndian

Endianess of multi-bytes pixel data for this stream.

GevSCPSPacketSize

Specifies the stream packet size, in bytes, to send on the selected channel for a GVSP
transmitter or specifies the maximum packet size supported by a GVSP receiver.

GevSCPD

Controls the delay (in timestamp counter unit) to insert between each packet for this
stream channel.

GevSCDA

Controls the destination IP address of the selected stream channel to which a GVSP
transmitter must send data stream or this destination IP address from which a GVSP
receiver may receive data stream.

GevSCSP

Indicates the source port of the stream channel.

UserSetControl

Name

Description

UserSetSelector

Selects the feature User Set to load, save or configure.

UserSetLoad

Loads the User Set specified by UserSetSelector to the device and makes it active.

UserSetSave

Save the User Set specified by UserSetSelector to the non-volatile memory of the
device.

UserSetDefaultSelector

Selects the feature User Set to load and make active by default when the device is reset.

IPEngine

Name

Description

ProgrammableLogicController

Category that contains the Programmable Logic Controller (PLC) features.

For more information please contact Aegis Electronic Group, Inc. *(888)687-6877 *[email protected] *http://www.aegiselect.com

Aegis

Electronic

Group,

Inc.

«
...
56
57
58
59
60
...
»

Summary of Contents for STC-SBS312POE































































Reviews:

No comments

Related manuals for STC-SBS312POE

Brand: Vacron Pages: 5

Brand: Vacron Pages: 2

Brand: IFM Pages: 9

E-P2 - PEN 12.3 MP Micro Four Thirds Interchangeable Lens Digital...

Brand: Olympus Pages: 164

E-P2 - PEN 12.3 MP Micro Four Thirds Interchangeable Lens Digital...

Brand: Olympus Pages: 164

Brand: Teltonika Pages: 4

Brand: AIPTEK Pages: 60

Brand: JAI Pages: 72

LDH SAI200 Series

Brand: Dahua Pages: 48

Brand: Accu-Scope Pages: 19

Brand: Greenleaf Pages: 4

Brand: Santec Pages: 40

Lumix DMC-LC1PP

Brand: Panasonic Pages: 84

Lumix DMC-FT4EB

Brand: Panasonic Pages: 98

Brand: Panasonic Pages: 53

2170749 - Pronea S APS Camera

Brand: Nikon Pages: 42

Brand: Nikon Pages: 252

Brand: Nikon Pages: 45

Brands by name

0 1 2 3 4 5 6 7 8 9 A B C D E F G H I J K L M N O P Q R S T U V W X Y Z

Popular brands

Load more brands