Image Sensor for FH - 12 Megapixel
Digital Camera
FH-SM12/SC12
INSTRUCTION SHEET
Thank you for selecting OMRON product. This sheet pri-
marily describes precautions required in installing and
operating the product.
Before operating the product, read the sheet thoroughly to
acquire sufficient knowledge of the product. For your con-
venience, keep the sheet at your disposal.
Model
© OMRON Corporation 2014 All Rights Reserved.
NOTICE:
This product meets CISPR11 class A. The intended use of this product is in an
industrial environment only.
6.2 W max. (13 VDC)
Instruction Sheet (this sheet)
High speed mode: 5 m max.
Standard mode: Using FZ-VS(L)4: 15 m max.
Using a dedicated product other
than FZ-VS(L)4: 10 m max.
FH-SC12
FH-SM12
●
Performance specifications
FH-S
□
12 camera body is recommending installation by a screw hole of the body.
5 mounting surface of the bottom front, top, and both sides are possible.
( Rated torque M4
：
1.2N
･
m
／
M2.6
：
0.3N
･
m)
Item
Model
10 to 150Hz: half-amplitude: 0.35mm:(maximum acceleration: 50m/s
2
),
10 times for 8 minutes each in 3 directions
Shock resistance 150m/s
2
; 3 times each in 6 directions
Operating and storage: 35% to 85%
(with no condensation)
No corrosive gases
X, Y : ±0.31mm
∂x, ∂y : ±1.7°
Operating: 0 to 40 ℃(with no icing nor condensation)
Storage: -25 to 65 ℃ (with no icing nor condensation)
Power
consumption
Vibration
resistance
Shock resistance
Ambient
Temperature
Ambient
humidity
Ambient
environment
Center positional
accuracy of
optical axis
Materials
Accessories
Degree of
protection
IEC60529 IP40 (in-panel)
■
Ratings / Performance
Case: Aluminum
●
General specifications
Cable length
FL-TCC1 , FLV-TCC
□
(Connection with the lighting, be sure to be 10W, 0.9A
or less to the total value of the power consumption of
the lighting controller. )
Dedicated
lighting
controller
Approx. 320g
Weight
Camera cable
FZ-VS
□□
Name plate
Enhancing connetor
Camera cable
connector CH2
Camera cable
connector CH1
■
Connecting
●
Camera
Using the Camera cable FZ-VS
□□
(sold separately), connect the connector
on the back of the camera and the camera connector on Controller FH series.
■
Dimensions
（
Unit
：
mm
）
This product is not designed or rated for ensuring safety
of persons. Do not use it for such purposes.
Meaning of Alert Symbols
Alert statements
WARNING
PRECAUTIONS ON SAFETY
PRECAUTIONS FOR SAFE USE
PRECAUTIONS FOR CORRECT USE
Indicates a potentially hazardous situation which, if
not avoided, will result in minor or moderate injury,
or may result in serious injury or death. Additionally
there may be significant property damage.
WARNING
Be sure to respect following items for safety.
・Tighten all screws securely during installation.
・Do not connect the Sensor to the products other than the dedicated camera cable
(FZ-VS□□), controller (FH), lighting controller (FL-TCC1 and FLV-TCC□),
extension unit (FZ-VSJ). If the Sensor is connected to non-dedicated products and
turned the power on, the devices may be damaged and be heated to a high
temperature.
・If you suspect an error or malfunction, stop using the Controller immediately, turn
OFF the power supply, and consult your OMRON representative.
・Do not try to disassemble, repair, or modify the product.
・Be sure to dispose of the product as industrial waste.
Please observe the following precautions to prevent failure to operate, malfunction, or
undesirable effect.
1. Installation and storage of the product
Do not install in the following locations.
・Locations where the ambient temperature exceeds the rated temperature range.
・Locations subject to sudden temperature changes (where condensation will form).
・Locations subject to relative humidity outside the range of 35 to 85%.
* The camera cable FZ-VS
□□
has polarity. Be sure to connect the side
with the name plate on it to the controller.
・Locations where there are corrosive or flammable gases.
・Locations where there is dust, salt, or iron powder.
・Locations where the device will be subject to direct vibration or shock.
・Locations where there is strong scattered light.
・Locations exposed to direct sunlight
・Locations where there is splashing of water, oil, or chemicals.
・Locations where there is a strong electrical or magnetic field.
・Locations close to high-voltage devices and/or power devices
2. Cables
・When connecting or disconnecting the camera cable or lighting controller cable, be
sure to turn off the controller unit.
・Do not use the camera cable exceeding the specified length.
・When connecting the Sensor and the Controller (FH) with single camera cable,
connect the cable to CH1 of the camera connector.
・When connecting the Sensor and the Controller (FH) with two camera cables, the type
and length of the camera cable must be matched.
・When connecting the Sensor and the Controller (FH) with two camera cables, check
the CH numbers of the Controller side and Camera side before connecting.
・Up to three camera cables can be connected using the extension unit FZ-VSJ. Be
sure to use the recommended camera cable with FZ-VSJ.
・When connecting the camera cable, tighten the cable with the fixing screw with the
recommended torque (0.15 N・m). Applying excessive force to the camera connector
may cause failure of the product.
・Use the ferrite core equivalent to ZCAT2035-0930A (manufactured by TDK) at the
controller side of the camera cable.
・The camera cable FZ-VS□□ has polarity. Be sure to connect the side with the name
plate on it to the controller. Be sure to connect the side with the name plate on it to
the controller.
3. Mounting
･Please tighten up securely by rated torque(M4 : 1.2N･m), when fixing the camera body.
･Please use an exclusive mounting bracket (Model : FH-SM12-XLC (separate sale)),
when fixing this product and dedicated lighting controller (Model : FL-TCC1 and
FLV-TCC□).
･Please tighten up securely by rated torque(M4 : 1.2N･m / M2 : 0.15N･m), when fixing
the camera body, the mounting bracket and dedicated lighting controller.
･Please use M42 mount exclusive lens (Model : 3Z4S-LE VS-L□□□□ /M42-10).
4. Beam
・The beam center may vary for each camera. Be sure to confirm the center position of
the image using the monitor before mounting. In the nature of the materials used, the
beam center of this product may change for the number of pixels due to changes in
ambient temperature.
5. Maintenance
・Avoid using thinner, alcohol, benzene, acetone or kerosene to clean the product.
・If there is large dirt or dust attached to the imaging element, blow them off with
blower brush (for camera lens). Do not use your breath to blow the dust off.
・When the lens is not mounted, be sure to attach the M42-mount cap on the lens mount. If dirt or
dust is attached to the image elements, false detection or failure may occur.
・Be sure to attach a connector cap on unused connectors at the back of the camera.
Removing the connector cap may cause a foreign material entering in the camera,
causing false operation or failure.
・Do not connect devices to the extension connector other than the dedicated ones
(FL-TCC1 or FLV-TCC□).
6. Imaging element
・In the nature of imaging element, lines may appear in images due to measurement
conditions or gain setting value. This does not indicated a malfunction. Although
there may be multiple faulty pixels, this does not indicate a malfunction.
・
When connecting the product to the Controller with a single camera cable,
connect the cable to CH1 of the camera cable connector.
・
When connecting the product to the Controller with two camera cables,
connect it as shown below.
(connecting four Cameras)
CH1
Camera
FH-S
□□□
Controller
FH
Camera connector 0
Camera connector 1
Camera connector 2
Camera connector 3
Camera connector 4
Camera connector 5
Camera connector 6
Camera connector 7
CH2
CH1
CH2
CH1
CH2
CH1
CH2
Manufacturer:
Omron Corporation,
Shiokoji Horikawa, Shimogyo-ku,
Kyoto 600-8530 JAPAN
TRACEABILITY INFORMATION:
Representative in EU:
Omron Europe B.V.
Wegalaan 67-69
2132 JD Hoofddorp,
The Netherlands
Model
Item
FH-SC12
FH-SM12
Color CMOS
Corresponding to 1.76-inch
Picture element
Monochrome CMOS
Corresponding to 1.76-inch
4084(H)×3072(V)
Effective pixels
Pixel size
5.5（μm)×5.5(μm)
Image size
22.5㎜×16.9㎜ (Diagonal 28.14㎜)
Scanning method
Progressive
2CH:38.9fps
1CH:19.5fps
High speed
mode※1
Frame
rate
2CH:19.5fps
1CH:9.8fps
Standard
mode※1
Synchronization method
Internal
Video output
Digital 8 bits
Gain
1 to 5 times
Shutter speed
60μs to 100,000μs
Lens mounting ※2 M42 mount(Recommended lens : 3Z4S-LE VS-L□□□□/M42-10)
F mount(F mount adapter : FH-ADF/M42-10)
Partial scanning
4 line to 3072 line ( 4 line unit )
Operation indicator
Power ON : Green lighting／Power OFF : Black out
Number of camera
connections
Max 4 camera per 1 FH controller(Can be connected to up to eight by
combining the camera of FH-S □ 12 other than in connection 8CH controller)
*1 This Sensor has high speed mode and standard mode according to your
application. High speed mode can be set in the system settings.
*2 For optical diagrams, refer to FH manual or catalog.
4-4.5Dia.
58 ±0.1
58 ±0.1
31 ±0.1
35 ±0.1
4-4.5Dia.
MOUNTING SCREW HOLES MOUNTING SCREW HOLES
35
4-M4DEPTH5.0
40
5
31
40 （5）
8
IMAGE AREA
68
58
68
58
43.6
43.6
M42xP1.0
(M42 MOUNT)
4-M4 DEPTH5
4-M2.6 DEPTH5
(for F mount adapter)
OPTICAL AXIS
5
31
35
4-M4 DEPTH5
35
5
31
4-M4 DEPTH5
36
22
Operation
indicator
Operation indicator
■
Mounting about exclusive mounting bracket (Model : FH-SM12-XLC (separate sale))
There are the following two ways of use.
①
Please use this bracket when fixing this product and dedicated lighting
controller (Model : FL-TCC1 and FLV-TCC
□
).
Please use M2 screws and tighten up securely by rated torque(M2 : 0.15N
･
m),
when fixing this product and dedicated lighting controller.
②
Please use this bracket when fixing this product and the camera with
1/4-20UNC.
This bracket can be attached to all four sides of the direction of the camera.
Please use M4 screws and tighten up securely by rated torque(M4 : 1.2N
・
m)
※
The camera body is recommending installation by a screw hole of the body.
It's isn't necessary to use FH-SM12-XLC.
Suitability for Use
s
Omron Companies shall not be responsible for conformity with any standards,
codes or regulations which apply to the combination of the Product in the
Buyer’s application or use of the Product. At Buyer’s request, Omron will
provide applicable third party certification documents identifying ratings and
limitations of use which apply to the Product. This information by itself is not
sufficient for a complete determination of the suitability of the Product in
combination with the end product, machine, system, or other application or
use. Buyer shall be solely responsible for determining appropriateness of the
particular Product with respect to Buyer’s application, product or system.
Buyer shall take application responsibility in all cases.
NEVER USE THE PRODUCT FOR AN APPLICATION INVOLVING
SERIOUS RISK TO LIFE OR PROPERTY WITHOUT ENSURING THAT THE
SYSTEM AS A WHOLE HAS BEEN DESIGNED TO ADDRESS THE RISKS,
AND THAT THE OMRON PRODUCT(S) IS PROPERLY RATED AND
INSTALLED FOR THE INTENDED USE WITHIN THE OVERALL
EQUIPMENT OR SYSTEM.
See also Product catalog for Warranty and Limitation of Liability.
Oct, 2014
D
OMRON Corporation
Industrial Automation Company
Contact: www.ia.omron.com
Tokyo, JAPAN
OMRON ELECTRONICS LLC
2895 Greenspoint Parkway, Suite 200
Hoffman Estates, IL 60169 U.S.A.
Tel: (1) 847-843-7900/Fax: (1) 847-843-7787
OMRON ASIA PACIFIC PTE. LTD.
No. 438A Alexandra Road # 05-05/08 (Lobby 2),
Alexandra Technopark,
Singapore 119967
Tel: (65) 6835-3011/Fax: (65) 6835-2711
OMRON (CHINA) CO., LTD.
Room 2211, Bank of China Tower,
200 Yin Cheng Zhong Road,
PuDong New Area, Shanghai, 200120, China
Tel: (86) 21-5037-2222/Fax: (86) 21-5037-2200
OMRON EUROPE B.V.
Sensor Business Unit
Carl-Benz-Str. 4, D-71154 Nufringen, Germany
Tel: (49) 7032-811-0/Fax: (49) 7032-811-199
Regional Headquarters
