background image

8

F3SP-T01

Safety Precautions

 

!

WARNING

Do not operate the product in atmospheres containing 
flammable or explosive gas. Arcs or heating of relays 
during switching may cause fire or explosion.

Do not use a load that exceeds the contact ratings or 
switching capacity. Doing so may cause the product to fail 
to perform its specified functions, causing insulation failure, 
contact welding, or contact failure. It may also cause 
damage to the F3SP-T01 or burning.

The service life will depend on the switching conditions. Be 
sure to check the actual operating conditions using the 
actual devices, and make sure that the number of switching 
operations will not cause performance problems. If you 
continue to use the device with deteriorated performance, it may 
result in breakdown of insulation between circuits, or cause burning of 
the product.

Handle with Care

Do not drop the product or expose it to excessive vibration or shock. 
Doing so may prevent it from functioning properly.

Adhesion of Solvent

Do not allow solvents, such as alcohol, thinner, trichloroethane, or 
gasoline, to come into contact with the product. Such solvents may 
make the markings illegible and cause deterioration of parts.

Installation Location

Do not install or store the product in the following locations. Doing so 
may result in product failure or malfunction.

Locations subject to direct sunlight

Locations subject to temperatures outside the range 

10 to 55

°

C

Locations subject to humidity levels outside the range 35% to 85%

Locations subject to condensation due to extreme temperature 
changes

Locations subject to atmospheric pressures outside the range 86 
to 106 kPa

Locations subject to corrosive or flammable gases

Locations subject to shock or vibration in excess of the product 
ratings

Locations subject to exposure to water, oil, or chemicals

Locations subject to dust (including iron dust) or salts

Take appropriate and sufficient countermeasures when using the 
product in the following locations.

Locations subject to static electricity or other forms of noise

Locations subject to possible exposure to radioactivity

Locations close to power supply lines

Installation

Do not use products that have been dropped or have its internal 
parts disassembled. Specified characteristics may not be 
achieved, and may cause damage to the product or burning.

If the products are installed side-by-side, the rated current is 1 A. 
Do not exceed 1 A.

Use the F3SP-T01 in an enclosure that provides at least IP54 
degree of protection.

Installation and Wiring

Use the following electrical wiring for external I/O devices.

Compatible Ferrules

Use ferrules that meet the following standards for length and width. 
If the standards are not met, connection may fail, or the ferrules 
may not be able to be plugged in and out of the terminals.

Ferrule Dimensions (for Power Supply Terminal of F3SP-T01)

Recommended Ferrule and Crimping Tool

Precautions for Safe Use

Solid wire

0.2 to 1.3 mm

2

  AWG24 to 16

Flexible 
wires

1.3 to 2.0 mm

2

, AWG16 to 14

If flexible wires are used, terminate the wires with 
insulated ferrules (DIN 46228-4 compatible type) 
before connecting them.

Square 
Ferrules

Dimension A

1.0 to 2.3

The cross-sectional 
area after crimping 
must be less than 
4.8 mm

2

.

Dimension B

0.8 to 2.65

Cylindrical
Ferrules

Dimension C

0.8 dia. to 2.3 dia.

Type of

ferrule

Manufacturer

Size

Model

Recommended

crimping tool

Square 
Ferrules

Phoenix 
Contact

AWG24 AI0.25-8YE

UD6
ZA3

AWG22 AI0.34-8TQ

AWG20

AI0.5-10WH
AI0.5-8WH

AWG18

AI0.75-10GY
AI0.75-8GY

AWG16 AI1.5-10BK

AWG14 AI2.5-10BU

Weidmuller

AWG24 H0.25/12

PZ6 roto

AWG22 H0.34/12

AWG20

H0.5/16
H0.5/14

AWG18

H0.75/16
H0.75/14

AWG16 H1.5/16

Cylindrical 
Ferrules

Nichifu

AWG22

TGV TC-1.25-11T
TGN TC-1.25-11T

NH11
NH32
NH65

AWG20

AWG18

AWG16

B

C dia.

S

qu

are Ferr

u

les

Cylindrical Ferr

u

les

A

Summary of Contents for F3SP-T01











Reviews: