background image

7

Step 4

Change the unit number of the Controller to which the data is to be 
downloaded to the unit number of the Controller from which the data 
was uploaded. When uploading has been completed, turn OFF the 
power and disconnect the uploaded Controller (unit number 1) from 
the socket or change the unit number to avoid using the same unit 
number twice during the download.
In this example, change the unit number of the master from 1 to 5, 
and change the unit number of the Controller to which the data is to 
be downloaded from number 2 to number 1. The system 
configuration will change to the configuration shown in the following 
diagram.

Step 5

Select Copy Mode.
Turn ON the power and press the 

COPY

 Key for at least 1 s to enter 

the Copy Mode.

Step 6

Set the download mode and the copy destination. 
Use the 

DOWN

 Key to select 

down

 on Display No. 2. Press the 

UNIT

 

Key to select unit number 1. (The lowest unit number that is being 
uploaded will be displayed in the download unit number display. At 
initialization, there is no upload data, so the unit number display is 
blank.) 

Step 7

Press the 

UNIT

 Key for at least 1 s to start the download.

down

 will flash on the display during the download. 

The mode will return automatically to Run Mode when the download 
has been completed.

Step 8

Copying to Other Controllers

Repeat steps 4 to 7 to continue copying the data.
The following example shows copying data to unit number 3.
Turn OFF the power and change unit number 1 back to unit number 
2.
Change unit number 3, where the data is to be downloaded, to unit 
number 1. The system configuration is shown in the following 
diagram. Turn ON the power and follow steps 4 to 7 to copy data to 
unit number 3.

Step 9

Changing back to the original unit number.
After copying has been completed, turn OFF the power and change 
back to the original the unit numbers. 
In this example, turn OFF the power and change unit number 5 to 
unit number 1, and change unit number 1 to unit number 3.

23

0

0

Master Copy 

destination

E5ZN   5

E5ZN   1

E5ZN   3

copy

up

0

copy

down

1

copy

down

1

23

0

0

Master

Copy 
source  

Copy 
destination

E5ZN   5

E5ZN   2

E5ZN   1

Summary of Contents for E5ZN Series















Reviews: