background image

Multipoint Temperature Controller

 E5ZE-8

@D1@B-V2

3

Specifications

Ratings

Supply voltage

24 VDC

Operating voltage range

85% to 110% of rated supply voltage

Power consumption

15 W + 20% max. at rated supply voltage

Input

Input type

Thermocouple: K, J, R, S, T, E, B, N, L, U, W, PL-II
Platinum resistance thermometer: Pt100, JPt100

Input impedance

Thermocouple: 1 M

 min.

Rated platinum resistance 
thermometer current

1 mA

Control 
outputs

Standard (Heating side)

Voltage output (with short-circuit protecting function)

ON:

12 

±

 1.2 VDC

OFF:

0.5 VDC max.

Max. load current:

30 mA DC per point

Current output

Rated output range:

4 to 20 mA DC

Current output range:

0 to 22 mA DC

With an output value of 0%:

4

+0

/

–0.6

 mA DC

With an output value of 100%:

20

+2

/

–0

 mA DC

Max. load resistance:

600 

 per point

Cooling side

Open collector output (NPN)

Max. applied voltage:

30 VDC

Max. load current:

50 mA DC per point

ON residual voltage:

2 VDC max.

OFF leakage current:

1 mA DC max.

Alarm outputs

Temperature alarm:

The total output of all control points (alarm 1 NPN open collector output and 
alarm 2 NPN open collector output)

HB alarm (heater burnout detection): Total output of all control points (1-point NPN open collector 

output)

HS alarm (SSR failure detection):

Total output of all control points (1-point NPN open collector 
output)

Temperature controller error output (memory, set value, or hardware error):

1-point NPN open collector output

Max. applied voltage:

30 VDC

Max. load current:

50 mA DC per point

No. of input control points

8 input and 8 control points

Setting method

Via communication

Control modes

ON/OFF control
Hybrid of advanced PID control and fuzzy control
Manual operation

Memory bank input

No. of points: 8 for each control point
Designation method: Through communication or memory bank designation input

Memory bank designation inputs

With contact signal input 

ON short-circuit resistance: 1 k

 max.

OFF open resistance:

100 k

 min.

With no-contact signal input 

ON residual voltage:

2 VDC max.

OFF leakage current:

1 mA DC max.

Summary of Contents for E5ZE-8 D1 B-V2









Reviews: