manualshive.com logo in svg

Omron E5EZ-PRR Series, Manual

Share
Download
Omron E5EZ-PRR Series Manual Download Page 7

Digital Position-Proportional Controllers

 

E5EZ-PRR

35

Nomenclature

■

E5EZ-PRR

MANU

A/M

PV

SV

MV

A

M

No. 1 Display

Operation Indicator

Temperature Unit

Mode Key

Level Key

Down Key

Up Key

No. 2 Display

No. 3 Display

Automatic/ Manual Key

Press this level key to select parameters.

The temperature unit is displayed when the display 
unit parameter is set to temperature.
The value selected for the temperature units 
parameter determines the unit displayed.
When set to ˚C, 

C

 is displayed, and when set to ˚F, 

F

 

is displayed.

1. ALM1 (Alarm 1): Illuminated when Alarm 1 output 

is on.

ALM2 (Alarm 2): Illuminated when Alarm 2 output 

is on.

2. OUT1, OUT2 Control Output 1(OPEN) and 

2(CLOSE)

Illuminated when control output 1 and/ or control 

output 2 are on.

3. STOP (Stop)

Illuminated when operations are stopped. 

Illuminated during controls when time input or the 

start/ stop function is stopped. Not illuminated in 

any other cases.

4. CMW (Communications Writing Control)

Illuminated when communications writing is 

enabled. Not illuminated in any other cases.

5. MANU (Manual Control)

Illuminated during manual mode. Not illuminated in 

any other cases.

Displays the process value or the designated data type.
Fully illuminated for approximately one second upon 
start-up.

Displays setting values, reading values, and input 
values. 
Fully illuminated for approximately one second upon 
start-up.

When valve opening display is on, it displays the 
percentage of the valve’s opening. 
No display when valve opening display is switched off.

Every time that this key is pressed, the figure shown in No. 2 Display will decrease. 
Changes in the displayed value accelerate as the time that the key is pressed 
decreases. In manual mode, pressing the 

D

 key will switch on control output 2 

(closed side output).

This automatic/ manual key makes the switch 
between automatic mode and manual mode. When 
this key is pressed for at least 1 second (unrelated to 
the time at which the key is released), the unit will 
switch modes.

Every time that this key is pressed, the figure shown 
in No. 2 Display will increase. Changes in the 
displayed value accelerate as the time that the button 
is pressed decreases. In manual mode, pressing the 

U

 key will switch on control output 1 (open side 

output).

Press this key to select the setting level.
The sequence of setting level selection is:
operation level       Adjustment level,
Initial input level        Communications 
setting level.

Summary of Contents for E5EZ-PRR Series























Reviews:

No comments

Brands by name

Popular brands

Load more brands