background image

1

Temperature Controller

E5AX-P

A 96 x 96 mm (DIN) Controller for
Control Valves

Controls motor valves without a potentiometer.

Optimum PID control with feed-forward control
circuitry.

High precision regardless of the set temperature.

Compatible with various inputs (input selected via
internal switch).

Models with communications capabilities also
available.

Ordering Information

 Electronic Temperature Controller

Communica-
tions

None

RS-232C

RS-422*

RS-485*

BCD

Transmission

 output*/**

(4 to 20 mA)

Communications

Board Add-on Type

Model

E5AX-PRR

E5AX-PRR01

E5AX-PRR02

E5AX-PRR03

E5AX-PRR20

E5AX-PRRF

E5AX-PRRM

*The Controller can also be equipped with a terminal block to connect communications. Specify a terminal block by adding “-X” to the model

number. Example: E5AX-PRR02-X

 **Capable of transmitting the process value or output value, but remote setting by external input is not possible.

 Temperature Ranges

Input (switch

selectable)

Thermocouple

Temperature

resistance

thermometer

Chromel vs.

alumel

J/L 

Iron vs.

constantan

T/U 

Copper vs.

constantan

Chromel

vs.

constantan

R

Platinum vs.

platinum

13% rhodium

S

Platinum vs.

platinum  10%

rhodium

PT platinum

resistance

thermometer

(Pt100/JPt100)

Range

%

C

–200 to 1,300

–100 to 850

–200 to 400

0 to 600

0 to 1,700

0 to 1,700

–99.9 to 450.0

%

F

–300 to 2,300

–100 to 1,500

–300 to 700

0 to 1,100

0 to 3,000

0 to 3,000

–99.9 to 800.0

Resolution (

%

C/

%

F)

(main settings and
alarm)

1

0.1

 Communications Boards

Communications

RS-232C

RS-422

RS-485

BCD

Transmission output

(4 to 20 mA)

Model

E53-X01

E53-X02

E53-X03

E53-X20

E53-XF

Summary of Contents for E5AX-P Series















Reviews: