EN-17
Param-
eter
Num-
ber
Name
Description
Initialize Data
A1-00
Language
selection for
Digital Opera-
tor dis-
play(JVOP-
160-OY only)
0:English
2:German
3:French
4:Italian
5:Spanish
6:Portuguese
A1-01
Parameter
access level
0:Monitoring only (Monitoring drive
mode and setting A1-01 and A1-
04.)
1:Used to select user parameters
(Only parameters set in A2-01 to
A2-32 can be read and set.)
2:Advanced
(Parameters can be read and set in
both, quick programming mode (Q)
and advanced programming mode
(A).
A1-03 Initialize
0:
No initializing
1110:Initializes using the user
parameters
2220:Initializes using a two-wire
sequence. (Initializes to the factory
setting.)
3330: Initializes using a three-wire
sequence.
Sequence / Reference Source
b1-01
Reference
source selec-
tion
Sets the frequency reference input
method.
0:Digital Operator
1:Control circuit terminal (analog
input)
2:Serial communication (RS422 /
485)
3:Option Card
b1-02
RUN com-
mand source
selection
Sets the run command input method.
0:Digital Operator
1:Control circuit terminal (digital
inputs)
2:Serial communication (RS422 /
485)
3:Option Card
b1-03
Stopping
method selec-
tion
Selects the stopping method when
the Run signal is removed
0:Deceleration to stop
1:Coast to stop
2:DC injection to stop
3:Coast to stop with timer (New Run
commands are disregarded while
coasting.)
b1-04
Prohibition of
reverse opera-
tion
0:Reverse enabled
1:Reverse disabled
2:Output Phase Rotation (both rota-
tional directions are enabled)
3:Output Phase Rotation with
Reverse disabled.
Speed Search
b3-01
Speed search
selection (cur-
rent detection
or speed cal-
culation)
Enables/disables the speed search
function and sets the speed search
method.
0:Disabled, speed calculation
1:Enabled, speed calculation
2:Disabled, current detection
3:Enabled, current detection
b3-14
Bi-directional
speed search
selection
Disables or enables the bi-directional
capabilities of the speed search func-
tion.
0:Disabled
1:Enabled
PI Control
b5-01
PI control
mode selec-
tion
0:Disabled
1:Enabled
3:PI control enabled
(frequency reference
+ PI output)
b5-02
Proportional
(P) gain
Sets the proportional gain of the PI
controller. P control is not performed
when set 0.00.
b5-03
Integral (I)
time
Sets the integral time of the PI con-
troller. I control is not performed when
set to 0.0 sec.
b5-09
PI output
characteris-
tics selection
Selects forward/reverse direction for
PI output.
0:PI output is forward
1:PI output is reverse.
b5-17
Accel/decel
time for PI ref-
erence
Sets the accel/decel time for the PI
Softstarter (SFS).
b5-18
PI Setpoint
Selection
0:Disabled
1:Enabled
b5-19
PI Setpoint
PI target value
Acceleration / Deceleration Settings
C1-
Acceleration/
Deceleration
times
Sets the time to accelerate/decelerate
from 0 Hz to the maximum output fre-
quency.
S-Curve Settings
C2-
S-curve char-
acteristic time
at acceleration
Sets the S-curve characteristic at
acceleration start and end.
Carrier Frequency
C6-02
Carrier fre-
quency selec-
tion
Selects the carrier frequency (factory
setting depends on Inverter capacity)
0: Low noise, low carrier
1: 2.0 kHz
2: 5.0 kHz
3: 8.0 kHz
4: 10.0 kHz
5: 12.5 kHz
6: 15.0 kHz
F: Programmable pattern
Speed Settings
d1-01
to
d1-04
Multi speed
references 1
to 4
Sets the multi-step speed references.
d1-17
Jog fre-
quency refer-
ence
Reference Limits
d2-01
Frequency ref-
erence upper
limit
Sets the frequency reference upper
limit in percent of the max. output fre-
quency (E1-04)
d2-02
Frequency ref-
erence lower
limit
Sets the frequency reference lower
limit in percent of the max. output fre-
quency (E1-04)
Param-
eter
Num-
ber
Name
Description
User Parameters
