background image

LCD Digital Operator 

 

LCD Digital Operator User's Manual v0_90 110218.doc 

Issue 0.90 Draft 

 

 

 

2.1. Operation Key 

 

 

NO.  Key image 

Key Name 

Function 

 

REMOTE 

It  changes  from  Local  to  Remote  mode.  Press  the  key 
during  2  seconds  to  change  from  Local  to  Remote  or 
Remote to Local. When  it  is  in  Local the OPE  led  will  be 
ON.  Use  Local  to  control  the  motor  with  LCD  digital 
operator keys (Run Fwd, Run Rev and Stop/Reset).  

 

READ 

It  transfers  inverter  parameters  to  the  LCD  digital  operator’s 
memory. (Refer to chapter 4 for more details.) 

 

WRITE 

It  copies  one  Parameter  Set  or  a  Parameter  Set  +  EzSQ 
(Drive  Programming)  saved  in  LCD  digital  operator  to  the 
inverter. (Refer to chapter 4 for more details.) 

 

ESC 

It returns to the above layer. 

 

SET 

It  jumps  to  the  below  layer  or  stores  the  change  introduced 
on the edit layer (after that it jumps to the above layer). 

 

UP 

It is used to move up the cursor, it increases a function code 
in 1 or increases a parameter value. 

 

DOWN 

It  is  used  to  move  down  the  cursor,  it  decreases  a  function 
code in 1 or it decreases a value. 

 

LEFT CURSOR 

It  is  used  to  move  the  cursor  to  the  left  or  it  moves  to 
previous mode when the display is at navigation level. 

 

RIGHT CURSOR 

It is used to move the cursor to the  right, or it moves  to the 
next mode when the display is at navigation level. 

10 

 

FWD RUN 

It  is  used  to  run  forward  the  motor  only  when  the  operation 
command (A002) is set in Digital operator. 
(Check KEY ENABLED LED) 

11 

 

REV RUN 

It  is  used  to  run  reverse  the  motor  only  when  the  operation 
command  (A002)  is  set  in Digital operator  
(Check KEY ENABLED LED) 

12 

 

STOP/RESET 

It  is  used  to  stop  the  motor  or  reset  an  alarm.  It  is  also 
possible  to  invalidate  the  STOP  key  by  B087  parameter.  
Besides it does  not response when LCD digital operator is 
reading or writing the parameters from/to the inverter. 

Summary of Contents for AX-OP05-E





























Reviews: