background image

LCD Digital Operator 

 

LCD Digital Operator User's Manual v0_90 110218.doc 

28 

Issue 0.90 Draft 

 

 

 

9. Battery exchange 

 

There is a real time clock IC built-in. The power is supplied by a battery when outside power supply 
is turned off

.

 When the battery comes to its life, the clock IC does not renew the time when power 

supply of LCD digital operator is turned off. 
The clock date stored in the IC will be reset to a default value January 1, 2001 when power supply of 
LCD digital operator is turned on. Thus, the time of Trip mode, Read mode and Write mode cannot 
be displayed correctly unless the time is set properly in Option mode after power supply of LCD digital 
operator is turned on. However, there is no special bad influence for operating except displaying 
proper time. 
When exchanging the battery, please disassemble the case by removing four screws backside of the 
operator. The plus pole of the battery (flat one) must be installed. Please take out the old battery using 
a thin minus driver, and be careful not to damage PCB and any part on the PCB. 
 

 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 
 

 

 

 

 

 

 

 

     Battery 

 
 

 

 

 

 

 

 

 

          +   

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

 

          +   

 

 

 

 

 

 

 

 

        _   

  
 

 

Change battery 
Name: Coin type lithium battery 
Recommended Type: 
   CR1220 (made by MAXELL) 
 

Summary of Contents for AX-OP05-E





























Reviews: