Omnitronic DJP-604 User Manual Download Page 18

 

 

 

 

18 

 EN 

Operation

  

To  protect  your  audio  equipment,  specifically  your  speakers,  follow  this  power-up  sequence:  Set  all  output 
volume controls of any equipment to minimum. Switch on  your audio sources first, then the amplifier. Then 
turn up the volume control on your sources (if provided) and set the output volume for each PA zone on the 
amplifier as needed. The SIG indicator will light up when a specific signal level has been reached. In case of 
overload the CLIP indicator lights up. If it lights continuously, turn back the corresponding level control. For 
switching off, follow the inverse sequence: always switch off the amplifier first and then the audio sources.  
 
 

7  

Cleaning and Maintenance 

DANGER TO LIFE! Disconnect from mains before starting maintenance operation! Please use a soft lint-free 
and moistened cloth. Never use alcohol or solvents! 
 
There are no serviceable parts inside the device. Maintenance and service operations are only to be carried 
out by authorized dealers.  
 
Should  you  need  any  spare  parts,  please  use  genuine  parts.  If  the  power  supply  cable  of  this  device 
becomes damaged,  it has  to be replaced by a special power supply cable  available at  your dealer. Should 
you have further questions, please contact your dealer. 
 
 

8  

Protecting the Environment 

 

Disposal of old equipment

 

 

 

When  to  be  definitively  put  out  of  operation,  take  the  product  to  a  local  recycling  plant  for  a 
disposal  which  is  not  harmful  to  the  environment.  Devices  marked  with  this  symbol  must  not  be 
disposed  of  as  household  waste.  Contact  your  retailer  or  local  authorities  for  more  information. 
Remove any inserted batteries and dispose of them separately from the product. 

You  as  the  end  user  are  required  by  law  (Battery  Ordinance)  to  return  all  used 
batteries/rechargeable  batteries.  Disposing  of  them  in  the  household  waste  is  prohibited.  You 
may  return  your  used  batteries  free  of  charge  to  collection  points  in  your  municipality  and 
anywhere  where  batteries/  rechargeable  batteries  are  sold.  By  disposing  of  used  devices  and 
batteries correctly, you contribute to the protection of the environment. 

 

 

Summary of Contents for DJP-604





















Reviews: