Omnimount 5.0 W/C, User Manual

Page: 2 / 2

•
Insert the hex key into the tension screw
head and tighten (see Fig. O)
Caution: Tightest is not always the best! Over
tightening fasteners can weaken the installation.
Make sure the connection is extremely solid and then
stop tightening.
•
If the speaker angle must be changed, do
not attempt to move the speaker without
first loosening the tension screw.
Reposition, then tighten the tension
screw further until the speaker is held
firmly in place.
•
If rotational adjustment of the mounted speaker is
required, the jam nut must first be loosened, the
speaker rotated, and the jam nut tightened again. Use
the 7/16” (11mm) open wrench or a small adjustable
crescent wrench for this procedure.
Caution: If the speaker loses its position, do not
attempt to move the speaker without first loosening the
tension screw. Reposition, then tighten the tension
screw further until the speaker is held firmly in
place.
CONGRATULATIONS! CONGRATULATIONS! CONGRATULATIONS! CONGRATULATIONS! CONGRATULATIONS!
YOUR INSTALLATION IS NOW COMPLETE. YOUR INSTALLATION IS NOW COMPLETE. YOUR INSTALLATION IS NOW COMPLETE. YOUR INSTALLATION IS NOW COMPLETE. YOUR INSTALLATION IS NOW COMPLETE.
Note: The following is made in lieu of all warranties expressed or
implied. The Manufacturer’s only obligation shall be to replace
parts of this product proved to be defective within two years of the
date of purchase. We are aware that this mounting assembly may be
used for purposes and in ways other than those for which it had been
designed and manufactured. The Manufacturer, Distributor, Retail
and their respective agents cannot be held responsible or liable for
injuries or property damage—direct, indirect, or consequential—
arising out of the use, or inability to use this product safely and
properly.
Note: Every effort has been made to provide accurate and error-free
assembly and installation information. Omnimount Systems
disclaims liability for any difficulties arising from the interpretation
of information contained in these instructions.
Copyright 2002, Omnimount Systems, Inc. All rights reserved. OmniMount
products are covered by patents issued and/or pending. “OmniMount” is a registered
trademark of Omnimount Systems, Inc. OmniMount products are manufactured in the
USA. Printed In the USA. Part#: 1001361
5.0 speaker mount kit Rev 11/02
OMNIMOUNT SYSTEMS, INC. OMNIMOUNT SYSTEMS, INC.
OMNIMOUNT SYSTEMS, INC. OMNIMOUNT SYSTEMS, INC. OMNIMOUNT SYSTEMS, INC.
8201 South 48 8201 South 48 8201 South 48 8201 South 48 8201 South 48 th th th th th Street Street Street Street Street
Phoenix, AZ 85044-5355 Phoenix, AZ 85044-5355 Phoenix, AZ 85044-5355 Phoenix, AZ 85044-5355 Phoenix, AZ 85044-5355
Voice: 480-829-8000 Voice: 480-829-8000 Voice: 480-829-8000 Voice: 480-829-8000 Voice: 480-829-8000
Fax: 480-756-9000 Fax: 480-756-9000 Fax: 480-756-9000 Fax: 480-756-9000 Fax: 480-756-9000
Email: Email: Email: Email: Email: hdqrs@omnimount.com hdqrs@omnimount.com hdqrs@omnimount.com hdqrs@omnimount.com hdqrs@omnimount.com
Web: Web: Web: Web: Web: www.omnimount.com www.omnimount.com www.omnimount.com www.omnimount.com www.omnimount.com
•
Pick up the vice grip pliers, regular
pliers, or small crescents wrench and
use one of these tools to assist in
tightening the tension screw. Tighten in
½ turn increments until the speaker is
firmly held in place.
Step 5: Step 5: Step 5: Step 5: Step 5:
ADJUSTING THE POSITION OF THE SPEAKER AND TIGHTENING THE ADJUSTING THE POSITION OF THE SPEAKER AND TIGHTENING THE ADJUSTING THE POSITION OF THE SPEAKER AND TIGHTENING THE ADJUSTING THE POSITION OF THE SPEAKER AND TIGHTENING THE ADJUSTING THE POSITION OF THE SPEAKER AND TIGHTENING THE
CLAMP ASSEMBL CLAMP ASSEMBL CLAMP ASSEMBL CLAMP ASSEMBL CLAMP ASSEMBLY YY YY
Fig. O
Step 6: Step 6: Step 6: Step 6: Step 6:
Securing the Speaker Wire to the Ball Shaft Securing the Speaker Wire to the Ball Shaft
Securing the Speaker Wire to the Ball Shaft Securing the Speaker Wire to the Ball Shaft
Securing the Speaker Wire to the Ball Shaft
•
You can help to enhance the appearance of the installation
with the two small tie wraps that have been provided in
your kit:
•
Position the wire on the ball shaft. Wrap one of the tie wraps
around both the ball shaft and wire. Repeat this step for the
second tie wrap.
•
Loop the open end of the tie
wrap into the slot in the other
end. Pull tie wrap closed.
Repeat this step for the second
tie wrap.
•
Using a small pair of wire
cutters, snip the extra lengths of
the tie wrap off-as close as
possible to the wrap “buckle.”