manualshive.com logo in svg

Omnia Omnia-3, Installation And Operation Manual

Share
Download
Omnia Omnia-3 Installation And Operation Manual Download Page 10

 

10

Table of Contents 

 
HAZARD / WARNING LABELS 

4 

Manual Update Notification 

6 

SPECIFICATIONS 7 
Omnia-3 Quick-Start Setup Guide 

11 

Chapter-1: Installation 

12 

Pre-Installation Tasks.............................12 
Installation & Connections ....................14 
Powering Up ..........................................17 

Chapter 2: The User Interface 

18 

Using the Jog Wheel ..............................18 
Main Menu Orientation..........................19 
User Interface Tutorial...........................19 
User Interface Concepts.........................21 
Bargraph Display Metering Screens ......22 
Menu Descriptions .................................23 

Chapter 3: Processing Overview 

30 

The Omnia-3 and Audio Processing ......30 

Chapter 4: Omnia-3fm Turbo 

32 

Processor Location.................................32 
Omnia-3fm Turbo Connections .............33 
Processing Presets..................................35 
Omnia-3fm Turbo System Adjustments 35

 

    FM Turbo Processing Worksheet          38 
Chapter 5: Omnia-3am 

39 

Processor Location.................................39 
Processing Presets..................................39

 

Omnia-3am System Adjustments ..........40

 

    AM Processing Worksheet  

        43 

Chapter 6: Omnia-3net/drm 

44 

Omnia-3net/drm Connections................44 
Omnia-3net/drm System Adjustments...44

 

    NET Processing Worksheet 

        45 

Chapter 7: Editing Presets 

46 

Preset Editing Overview ........................46 
The Processing Display..........................47 
Parameter Editing...................................49 
Saving, Renaming and Deleting Presets 53 
Getting The Sound You Want................53 

Chapter 8: Remote Control for FM Turbo 57 

Software Installation ..............................57 
Setting Up and Configuring Omnia 
Remote Control......................................58 
Using the Remote Control .....................64 
Using a Terminal Program and Direct 
Connection .............................................65 
Trigger Interface and Script Editor ........66 

Chapter 9: Remote Control for v3.3.x and 
Earlier 74 

Software Installation ..............................75 
Setting Up and Configuring Omnia 
Remote Control......................................75 
Using the Remote Control .....................81 
Using a Terminal Program and Direct 
Connection .............................................82 
Trigger Interface and Script Editor ........83 

Chapter 10: Troubleshooting 

92 

Omnia Messages ....................................93

 

    Diagnostic and Error Messages 

Electrical and mechanical safety note! ..95 
Narrowing down problems ....................96 
Obtaining Service...................................97 

WARRANTY 98 

Summary of Contents for Omnia-3



































































































Reviews:

No comments

Brands by name

Popular brands

Load more brands