Omni Sonic Ruptor 400 User Manual Download Page 3

 3 

 

This manual is a guide for the use of the Sonic Ruptor 400 Ultrasonic Homogenizing System 
and accessories.  
 
Data herein has been verified and validated. It is believed adequate for the intended use of the 
instrument. If the instrument or procedures are used for purposes over and above the  
capabilities specified herein, confirmation of the validity and suitability should be obtained,  
otherwise Omni International does not guarantee results and assumes no obligation or  

liability. This publication is not a license to operate under, or a recommendation to infringe 
upon, any process patents.  
 
Notes, cautions, and warnings within the text of this manual are used to emphasize important 
and critical instructions. 
 
This Omni International product is warranted to be free from defects in material and  
workmanship for a period of ONE YEAR from the date of delivery. Omni International will 
repair or replace and return free of charge any part which is returned to its factory within said 
period, transportation prepaid by user, and which is found upon inspection to have been  
defective in materials or workmanship. For the first 90 days, both parts and service are  
without charge. For the balance of the period, parts will be provided but service will be 
charged at established labor rates. This warranty does not include normal wear from use;  it 
does not apply to any instrument or parts which have been altered by anyone other than an 
employee of Omni International nor to any instrument which has been damaged through  

accident, negligence, failure to follow operating instructions, the use of electric currents or 
circuits other than those specified on the plate affixed to the instrument, misuse, or abuse. 
Omni International reserves the right to change, alter, modify, or improve any of its  
instruments without any obligation whatever to make corresponding changes to any  
instrument previously sold or shipped. 
 
THE FORGOING OBLIGATION IS IN LIEU OF ALL OBLIGATIONS AND LIABILITIES  
INCLUDING NEGLIGENCE AND ALL WARRANTIES OF MERCHANTABILITY OR  
OTHERWISE, EXPRESSED OR IMPLIED IN FACT OR BY LAW, AND STATE OUR ENTIRE 
AND EXCLUSIVE LIABILITY AND BUYERS EXCLUSIVE REMEDY FOR ANY CLAIM OF 
DAMAGES IN CONNECTION WITH THE SALE OR FURNISHING OF GOODS OR 
PARTS, THEIR DESIGN, SUITABILITY FOR USE, INSTALLATION, OR OPERATION. OMNI 
INTERNATIONAL WILL IN NO EVENT BE LIABLE FOR ANY SPECIAL OR  
CONSEQUENTIAL DAMAGES WHATSOEVER, AND THEIR LIABILITY UNDER NO  
CIRCUMSTANCES WILL EXCEED THE CONTRACT PRICE FOR THE GOODS FOR 

WHICH LIABILITY IS CLAIMED. 

 WARRANTY 

INFORMATION

 

Summary of Contents for Sonic Ruptor 400





















Reviews: