Page - 8
Page - 13
Feature #1 Remote Start Run Time
Factory Default Setting
10 Minutes
(
press
“lock” button to program
)
Options:
5 Minutes
(
press
“unlock” button to program
)
15 Minutes
(
press “trunk” button to program
)
20 Minutes
(
press
“start” button to program
)
This feature sets the period of time that the engine will run after being remotely
started. If the engine is not stopped by controller/transmitter command or a safety
circuit violation, the engine will automatically stop upon the expiration of the
selected time period. Caution: The remote engine starting feature should
NEVER be used when the vehicle is parked in an enclosed structure or garage.
The User Programmable Features
- SEE PAGE 12 FOR PROGRAMMING INSTRUCTIONS -
Each of the Programmable Features is described in detail in the
following pages. The User Programmable Features are described as a
first group, and the Installer Programmable Features as a second group.
This group of User Programmable Features are all accessed as a group in the first
level of features’ programming. These features have a direct affect upon the
system’s operations, so the programming and operation of each are described.
The Excalibur RS-310-EDP’s 6
User Programmable Features
:
1
Remote Start Run Time
2
Steady / Flashing Lights During Remote Start
3
Confirmation Chirps / Volume
4
Pulsed Horn / Steady Siren
5
Doors Lock With Ignition On
6
Doors Unlock With Ignition Off
Use the step-by-step instructions on page 12, and the complete features matrix
on page 19, to change any of the programmable features. Each feature, the option
choices and related programming controller/transmitter button assignment are
described in detail in the following pages.
Valet Mode
The system may be placed into a “valet mode” which prevents the
remote start feature from being activated. It also disables confirmation
chirps when locking or unlocking the doors. Valet Mode should always be
used when you do not wish for remote starting to be operated, such as
when you have your vehicle serviced.
The Valet Switch, is used to engage Valet Mode:
•
With the system in an unlocked state, press and hold the Valet Switch
for 3 seconds; the Status Light will light steady, to indicate Valet Mode, and
stay illuminated continuously while the system is in Valet Mode. The horn
will chirp once and the lights will flash twice.
Once in Valet Mode, an attempt to remote start will result in no response
from the system. Keep this in mind if remote start stops functioning. The
system may have accidentally been placed in valet mode. To check for
valet mode, turn the ignition key to the RUN/ON position, then back OFF.
If the system is in valet mode, the horn will chirp once.
•
To turn off Valet Mode, simply press & release the Valet Switch once.
The Status Light will turn off.
Using The Valet Switch
Emergency Override
If the system is in a locked state, you cannot perform some functions
like transmitter or feature programming. If the system is locked and you do
not have a transmitter to unlock the system, you can perform an emer-
gency override to access the programming functions.
•
With the system in a locked state, simply turn the ignition key to the
RUN/ON position.
•
Press and release the valet switch once.
You should now be able to access programming functions.
Pit-Stop Feature
This feature allows you to leave your vehicle and keep the engine run-
ning for quick errands. To use this feature, have the engine running nor-
mally from the ignition switch, have the gear selector in “park”, and your
foot off of the brake pedal. Press the Valet Switch twice; the parking lights
will flash once and the horn chirps 5 times; then turn the ignition off. The
engine will remain running for the programmed run time, or it will turn off if
another transmitter signal is received, a safety circuit is violated, or if the
Valet Switch is pressed.
Step 7
Allow 10 seconds to pass without performing any programming
actions, or turn the vehicle’s ignition on.
• The horn will sound briefly (and the Status Indicator Light will go out).
