Omega OO62PX, Operating And Installation Instructions

Page: 15 / 22

USING THE DIGITAL TIMER
Time of Day Adjustment:
The time must be adjusted before starting to use the oven. Following the
connection of the power supply to the oven, the display will begin to
flash. Leave the oven function control at “off” and then press either the
“+” or “-“ button (set to manual mode). Press the “+” or “-“ buttons to
set the correct time. Once correct, leave for 5 seconds to set.
As the displayed time will be reset in the event of a power failure or
power loss, the time adjustment operation will have to be performed
again before the oven will work.
Note: that the time can only be reset after the power has been reset.
Minute Minder:
This function can be used to receive an audible warning after a pre-set time. It is used as a reminder and does
not affect the cooking functions.
Press the Alarm Key button. The symbol BELL and 0:00 will appear on the screen. Adjust the desired time
period (HH:MM – up to 23.59) for the warning by using “+” or “-“ buttons. Shortly after the completion of the
adjustment, the current days’ time will be displayed confirming, the minute minder has been set. The time
can be adjusted if needed later by pressing the mode button again, and then with the “+” and “-“ buttons.
When the set time is up, the timer gives an audible warning and the symbol BELL turns off. Pressing either
the “+” or “-“ button will stop the audible warning.
The oven will not be turned off with this audible warning function.
14
Adjusting the Cooking Duration Time:
Adjusting the Cooking Duration Time:
This function is used to cook in the desired time range. The foods to be cooked are put into the oven. The oven is
adjusted to the desired cooking function. The oven temperature is adjusted to the desired degree depending on
the dish to be cooked. Touch on the “M” sensor until you see Duration time symbol “ |>| ” on the timer display
screen. “AUTO” appear s on the display. Adjust the cooking period for the food you wish to cook, by using the T “+”
or “-“ buttons while the timer is in this position. Some time after the adjustment operation is completed, the day's
time will appear on the screen and the Duration time symbol will begin to continuously light on the screen. At the
completion of the set duration, the timer will stop the oven and give an audible warning. Also, “AUTO” will begin to
flash on the screen. Touching any sensor of the control unit will end the audible warning. “AUTO” will go on to
flash. Touch “ - “ and “ + “ symbols at the same time to finish “AUTO” mode.
Adjusting the Cooking End Time:
This function is used to cook after a certain period of time, within certain duration. The food to be cooked is put into
the oven. The oven is adjusted to the desired cooking function. The oven temperature is adjusted to the desired
degree depending on the dish to be cooked.
Touch on the “M” sensor until you see Duration time symbol “ |>| ” on the timer display screen. “AUTO” appear on
the display. Adjusted the cooking period for the food you wish to cook, by using the Timer Plus and minus sensor
while the timer is in this position.Then touch the “M” sensor until you see “ >| ” symbol. the day time will begin to
flash, with the addition of the cooking period. Adjust the finishing time for the food by using the Timer Plus and
minus sensor while the timer is in this position. Some time after the adjustment operation is completed, the day time
will appear on the screen and the “ >| ” symbol will begin to continuously light on the screen. The oven will start
operating at the time calculated by deducting the cooking period from the set finishing time, and will stop at the set
finishing time. The timer will give an audible warning and “AUTO” will begin to flash on the screen will begin to flash.
Touching any button of the timer will end the audible warning. “AUTO” will go on to flash. Touch “ - “ and “ + “
symbols at the same time to finish “AUTO” mode.
Digital Timer Sound Adjustment:
Touch “-“ sensor until you hear sound. timer will give an audible signal beep. After that each time “-“ sensor is
touched, timer will give three different types of signal beep. Do not touch any further sensor and timer will save the
last selected signal type.
Key Lock Function
The key lock function is used to prevent operating any functions of the control unit by mistake. Touch “+” sensor until
you see key lock symbol on the display to activate key lock. Touch the “+” sensor to deactivate key lock.
While oven is operating, if control switches and touch buttons are not pushed
or touched for 6 hours, oven turns off.
14