background image

4

LED Indicator Functions

The red and green LEDs on the front of the OM-CP-
ULTRASHOCK-A and OM-CP-SHOCK300 will flash or maintain 
a static condition to represent operating functions as shown 
in the table below.

The power up indication is only presented if the battery pack 
is separated from the front face and replaced. This should be 
done only during factory service or if directed to do so by a 
Omega support or repair agent. If it is presented at any other 
time, there may be a malfunction of the unit.

OM-CP-ULTRASHOCK-A & OM-CP-SHOCK300 

Red LED 

Indicator

Green LED 

Indicator

OPERATING FUNCTION

GREEN LED INDICATOR

RED LED INDICATOR

Power-up Indicator

Flashes 4 times

 

Red and green LED indicators alternately and rapidly flash 4 times each at power-up. LED 

indicators continue to flash for error at power-up.

Logging Data  

(without USB connected)

Flashes every 15 seconds

 

Indicates normal operation of logger without 

USB connected and adequate battery charge 

level.

Flashes every 15 seconds (maximum) 

Indicates low battery charge level.

Logging Data 

(with USB communication)

Flashes every 15 seconds

 

Indicates normal operation of logger with USB 

connected.

Flashes every 5 seconds (maximum)

 

Indicates when logger communication occurs 

via USB.

Delayed Logging Start

Flashes every 3 seconds

 

Red and green LED indicators simultaneously flash every 3 seconds to indicate data logging 

delayed start is set.

USB Charging 

(USB connected)

Pulses slowly on and off

 

Indicates when battery is charging via USB 

connector.

Flashes every 5 seconds (maximum)

 

Indicates when logger communication occurs 

via USB.

Battery Charged 

(USB connected)

On

 

Indicates when battery is fully charged when 

connected to USB.

Flashes every 5 seconds (maximum)

 

Indicates when logger communication occurs 

via USB.

Battery Charging Fault 

(USB connected)

Off

 

On 2 seconds then off 2 seconds

 

Indicates when there is a battery charging fault 

and continues to flash until fault is cleared.

Logger Off

Off

 

Red and green LED indicators are off when logger is off and USB not connected.

Summary of Contents for OM-CP-SHOCK300












Reviews: