background image

 

 
 
 
 
 

GAS  CONNECTION 

 

This  appliances  is  suitable  for  installation  with  Natural 
Gas or ULPG 

Refer  to  page  11  for  the  relevant  burner  pressure  and 

appropriate  injector  sizes.  When  the  appliance  is  to  be 
connected  to  Natural  Gas  then  the  pressure  regulator 
supplied  must  be  fitted  to  the  gas  inlet. A  test  point  (for 
checking  the  gas  pressure)  is  supplied  either  with  the 

regulator  or  as  a  separate  fitting  in the  case  of  ULPG 

appliances.

 

 

Connection  of  the  appliance  to  the  gas  supply  must  be 
in  accordance  with  the  requirements  of AS5601.  A  ½ ”

 

BSP connector  at the  inlet is recommended  and the  gas

 

supply line to the appliance must be of adequate length

 

to  allow  sufficient  withdrawal  of  appliance  for  service  or 
disconnection and be:

 

 

a) 

annealed copper pipe; or 

b) 

a  hose  assembly  complying  with  the  requirements  of AS1869  - Class 

B, 1Omm diameter, maximum length 1OOOmm. 

 

The appliance  must  be installed with  provision to  allow the  gas to  be turned  off 
and  disconnected  for  servicing  and  removal  of  the  appliance  as  required  from 
the gas supply. 

Before  the  appliance  is  operated  make  certain  all  relevant  parts  are  placed  in 

the correct position. 
When the installation is completed the installation connections of appliance will require 
to  be  leak tested,  the  burner  operating  pressure  and flame  checked  and  adjusted. 
Warranty  service  calls  do  not cover  these  adjustments! 
To  check  the  operating  pressure  of  the  appliance  it  is  recommended  at  last  2 
large size burners are used. Ensure appliance is secured to wall when installation 
is completed. 

N.G. The  regulator  supplied  must  be fitted  to the 

½” 

BSP thread  at the  rear  of 

the  appliance.  An  approved  manual  shut-off  valve  must  be  installed.  The  N.G. 
regulator must be checked and adjusted to 1.0kPa after installation. 

 

ULPG Can be connected to the inlet fitting directly. The 

 

pressure must be checked to ensure it is operating at 

2.75kPa. A separate test point fitting must be installed 

between the piping & the appliance for the pressure to    

 

be checked to ensure it is operating at 2.75kPa. 

 

Summary of Contents for OG60XA















Reviews: