background image

4

1) BURNERS

A diagram is screen-printed above each knob on the

front panel. This diagram indicates to which burner

the knob in question corresponds. After having

opened the gas mains or gas bottle tap, light the

burners as described below:

- manual ignition

Push and turn the knob corresponding to the

required burner in an anticlockwise direction until it

reaches the full on position (large flame fig. 1), then

place a lighted match near the burner.

- Electrical ignition

Push and turn the knob corresponding to the

required burner in an anticlockwise direction until it

reaches the full on position (large flame fig. 1), then

depress and release the ignition button.

- Automatic electrical ignition

Push and turn the knob corresponding to the

required burner in an anticlockwise direction until it

reaches the full on position (large flame fig. 1), then

depress the knob.

- Lighting burners equipped with flame failure

device

The knobs of burners equipped with flame failure

device must be turned in an anticlockwise direction

until they reach the full on position (large flame

fig. 1) and come to a stop. Now depress the knob in

question and repeat the previously indicated

operations.

Keep the knob depressed for about 10 seconds

once the burner has ignited.

Note: you are advised not to try and light a

burner if the flame divider (Burner Cap) is not

correctly placed.

HOW TO USE THE BURNERS

Bear in mind the following indications in order to

achieve maximum efficiency with the least possible

gas consumption:

- Use adequate pans for each burner (consult the

following table and fig. 2).

- When the pan comes to the boil, set the knob to

the reduced rate position (small flame fig. 1).

- Always place a lid on the pans.

- Use only pan with a flat bottom and in thick metal.

WARNINGS:

- Burners with flame failure device may only be

ignited when the relative knob has been set to

the Full on position (large flame fig. 1).

- Matches can be used to ignite the burners in a

blackout situation.

- Never leave the appliance unattended when the

burners are being used. Make sure there are no

children in the near vicinity. Particularly make

sure  that  the  pan  handles  are  correctly

positioned and keep a check on foods requiring

oil and grease to cook since these products can

easily catch fire.

- The appliance must not be used by people

(including children) with impaired mental or

physical capacities, or without experience of

using electrical devices, unless supervised or

instructed by an expert adult responsible for

their care and safety. Children should not be

allowed to play with the equipment.

- DO NOT SPRAY AEROSOLS IN THE VICINITY OF

THIS APPLIANCE WHILE IT IS IN OPERATION.

- Do not place pans with an unstable or deformed

bottom on the burner, as these may tip or spill their

contents, causing accidents.

-  DO  NOT  USE  OR  STORE  FLAMMABLE

MATERIALS NEAR THIS APPLIANCE.

- Do not use the hob as a work surface.

- NOT FOR USE IN MARINE CRAFT, CARAVANS

OR MOBILE HOMES UNLESS EACH BURNER IS

FITTED WITH A FLAME SAFEGUARD.

- Containers  wider  than  the  unit  are not

recommended.

- DO NOT MODIFY THIS APPLIANCE.

- DO NOT USE AS A SPACE HEATER.

- This cooktop is not suitable for use with

aftermarket lid or cover.

USE

In the event of the Burner flames being accidentally

extinguished, turn off the burner control and do not

attempt to re-ignite the burner for a least 1 minute.

FIG. 1

Closed position

Full on position

Reduced rate

position

FIG. 2

Burner designation:

Double crown 

15.5 

MJ/h

12.6 MJ/h

24 - 26

Rapid

12.0 

MJ/h

10.4 MJ/h

20 - 22

Semirapid

7.1 

MJ/h

6.3 MJ/h

16 - 18

Semirapid reduc. 5.4 

MJ/h

4.9

16 - 18

Auxiliary

4.1 

MJ/h

3.6 MJ/h

10 - 14

Burners

Power ratings

Pan Ø 

in cm

Natural

U-LPG

Summary of Contents for OCG755FX

















Reviews: