background image

15

TECHNICAL ASSISTANCE AND SPARE PARTS

Before leaving the factory, this appliance will have been tested and regulated by expert and specialised

personnel in order to guarantee the best performances.

Any repairs or adjustments which may be subsequently required may only be carried out by qualified

personnel with the utmost care and attention.

For this reason, always contact your Dealer or our nearest After Sales Service Centre whenever repairs or

adjustments are required, specifying the type of fault and the model of the appliance in your possession.

Please also note that genuine spare parts are only available from our After Sales Service Centres and a

qualified retail outlets.

The above data are printed on the data label put on the inferior part of the appliance and on the packing label.

The above informations give to the technical assistant the possibility to get fit spare parts and a heaven-sent

intervention. We suggest to fill the table below.

MARK: ........................................................

MODEL: .....................................................

SERIES: .....................................................

FOR CUSTOMER SERVICE

CALL THE PHONE NUMBER PROVIDED IN

THE WARRANTY.

Keep the Warranty Certificate or the sheet of technical

data with the Instructions Handbook during the

appliance life. It contains important technical data.

This appliance is marked according to the European directive 2002/96/EC on Waste Electrical and

Electronic Equipment (WEEE).

This guideline is the frame of a European-wide validity of return and recycling on Waste Electrical and

Electronic Equipment.

Summary of Contents for OCG755FX

















Reviews: