background image

4

 

!

OPerATiOn

 

Lifting

 

 

Only attachments and/or adapters supplied by the manufacturer shall be used. Lift only on area of the

 

vehicle as specified by the vehicle manufacturer.

1. Follow the vehicle manufacturer’s recommended guidelines for lifting. Engage the emergency brake and chock 

each unlifted wheel in both directions to prevent inadvertent vehicle movement.

2. 

Close the release valve by turning the handle clockwise until firm resistance is felt.

3. Refer to the vehicle manufacturer owner’s manual to locate approved lifting points on the vehicle. Center jack 

saddle under lift point.

4. Verify lift point, then pump handle to contact lift point. To lift, pump handle until load reaches desired height.

5. Transfer the load 

immediately

 to appropriately rated jack stands.

          

NEVER

 use hydraulic jack as a stand alone device! 

ALWAYS

 transfer the lifted load 

IMMEDIATELY

 to a 

          pair of appropriately rated jack stands. Use one pair of jack stands per vehicle. Rated capacity is per 

pair only! Do not exceed rated capacity.

Lowering

          Be sure all tools and personnel are clear before lowering load. 

Slowly open the release valve!

 The more 

          you turn the handle counter-clockwise, the faster the load will come down. 

Maintain control

 of the rate

of speed at which the load lowers at all times!

1. Raise load high enough to clear the jack stands.

2. 

Remove jack stands carefully (

always

 used in pairs).

3. 

Slowly

 

turn the handle counter-clockwise, but no more than 1/2 full turn. 

If the load fails to lower:

  a. Use another jack to raise the vehicle high enough to reinstall jack stands.

  b. Remove the malfunctioning jack and then the jack stands.

  c. Use the functioning jack to lower the vehicle.

4. After  removing  jack  from  under  the  load,  fully  lower  the  saddle  to  reduce  ram  exposure  to  rust  and 

contamination.

 

!

 

!

!

   

WARNING

•  

Study, understand, and follow

 all printed 

materials provided with/on this product before use.

•  

do not

 exceed rated capacity.

•  Use only on hard, level surface.
•  

This is a lifting device only!

•  

Immediately

 after lifting, support the load with 

 

a pair

 of appropriately rated jack stands.

•  Lift only on areas of the vehicle as specified by 

the vehicle manufacturer.

•  

Do not move or dolly the vehicle while on the jack.

•  No alterations shall be made to this product.

FAiLUre

 TO HEED THESE MARKINGS MAY 

reSULT

 IN 

PerSOnAL inJUrY And/Or 

PrOPerTY dAMAGe

To avoid 

crushing and related injuries

:

• 

never

 work on, under or around a load supported 

only by hydraulic jack.

• 

Always

 use adequately rated jack stands.

• Chock each unlifted tire in both directions.
• 

do not

 use this device to lift, level, lower, support 

nor move a house, mobile home, travel trailer, 

camper or any building structure.

• 

Be alert

 and 

sober

 when using this product. Do not 

operate under the influence of drugs or alcohol.

!

   

WARNING

X

•  The paint on this product contains lead, a chemical known in 

the State of California to cause cancer, birth defects and other 

reproductive harm.  

•  Do not ingest paint chips and keep product away from children.  

•  Wash hands after each use.

WArninG

!

!

Summary of Contents for magiclift 29023









Reviews: