background image

1

SAFETY  INFORMATION

The following safety information must be observed to insure maximum

personal safety during the operation at this meter:

1. Do not use the meter if the meter or test leads look damaged, or if you

suspect that the meter is not operating properly.

2. This meter is not recommended for high voltage industrial use; for example,

not for measurements of 440 VAC or 600 VAC industrial power mains. The
unit is intended for use with low energy circuits to 600VDC or AC or high
energy circuit to 250 VAC or DC. Accidental misuse by connection across
a high voltage, high energy power source when the meter is set up for mA
measurement may be very hazardous.

3. Turn off power to the circuit under test before cutting, unsoldering, or

breaking the circuit. Small amounts of current can be dangerous.

4. Use caution when working above 60V dc or 30V ac rms. Such voltages pose

a shock hazard.

5. When Using the probes, keep your fingers behind the finger guards on the

probes.

6. Measuring voltage which exceeds the limits of the multimeter may damage

the meter and expose the operator to a shock hazard. Always recognize the
meter voltage limits as stated on the front of the meter.

7. If the equipment is used in a manner not specified by the manufacturer, the

protection provided the equipment may be impaired.

Summary of Contents for HHM17

















Reviews: