Step 1.
Enter the vehicle normally.
Step 2.
Using your key, turn "on" the ignition. Be prepared to perform the
following Step before 5 seconds expires.
Step 3.
Within 5 seconds, press and release the Easy Valet
TM
Switch. The system
will be immediately overridden.
Once the activated system has been overridden, if Valet Mode is desired, holding the Easy Valet
TM
Switch depressed for two seconds will place the system into Valet Mode.
Page - 8
Starter Disable
The E-2300
ATV
provides an active Starter Disable (which engages every time the transmitter is used
to lock the doors), and may be configured, if desired, to also provide an automatic (passive) Starter
Disable. The optional passive Starter Disable may qualify you for an insurance discount, so please
check with your insurance agent.
Active Starter Disable: Whenever the doors are locked via the transmitter, the Starter Disable will
instantly engage. Unlocking the doors with the transmitter will deactivate the Starter Disable circuit,
allowing the engine to be started. Please note that the Starter Disable may be configured to
automatically reengage 90 seconds after the doors are unlocked by the transmitter; or, to engage
automatically 90 seconds after the ignition switch is turned "off". These automatic Starter Disable
options are explained in more detail in the "User Programmable Features" section of this Owner's
Manual.
The E-2300
ATV
includes a built-in piezo buzzer for audible confirmation when a transmitter
command is received. This confirmation is designed to be heard only while inside the vehicle.
Standard Confirmation Operations
One Beep .................................................................... The transmitter has locked the doors and/or
the Starter Disable has engaged.
Two Beeps .................................................................. The transmitter has unlocked the doors and
the Starter Disable is disengaged.
Two Beeps .................................................................. The system has just been placed into Valet
(With LED Illuminated Steady) Mode.
Two Beeps When The
Ignition Switch Is Turned "Off" ................................. The system is reminding you that it is in
Valet Mode.
Special Confirmation Operations
Beeps For Two Seconds
When The Ignition Switch Is Turned "On" ................ The Automatic Transmitter Verification
feature system is alerting you that transmitter
programming activity has occurred within the
last 48 hours.
Audible Confirmation
Page - 9
Programming Transmitters To Operate Your Executive System: To use an additional or
replacement transmitter, it's unique digital code must first be added to the Executive System module's
memory. The dealership where you purchased your Executive System can provide and program
transmitters for you, or you may program the transmitters yourself. If you wish to program a
transmitter, please follow these Transmitter Programming Mode procedures carefully:
1) Have all the transmitters that you wish to operate your Executive System at hand. Any time
a transmitter code is programmed into your Executive System, all existing codes are
automatically erased. This, in addition to the Automatic Transmitter Verification
TM
feature,
prevents someone from adding an unauthorized transmitter to your system.
2) Within a 5 second period, turn the ignition switch "on" five times: "on", "off", "on", "off", "on",
"off", "on", "off", then "on" again; the fifth time leaving it "on". The buzzer will sound briefly
to indicate that the system is ready to receive transmitter codes.
3) Within 10 seconds press the LOCK button on the first transmitter you wish to encode to the
system. The buzzer will beep once to indicate the transmitter's code is learned by the system.
It is only necessary to press the LOCK button, as the rest of the transmitter's functions are
assigned automatically.
4) Repeat Step 3 within 10 seconds for each additional transmitter. The system will leave
Transmitter Programming Mode when the ignition switch is turned "off", after 10 seconds of
not receiving a transmitter broadcast, or upon learning the fourth transmitter.
Programming Transmitters
Page - 10
User Programmable Features
Page - 11
Your E-2300
ATV
has four User Programmable Features which may be easily configured to your
requirements as part on the Transmitter Programming Mode. Once Transmitter Programming Mode
has been accessed (described on the previous page), at the point where the first transmitter code is
entered and acknowledged, that same transmitter may be used to configure these User Programmable
Features as desired. The User Programmable Features, and their factory default settings, are:
1) The Doors Automatically Lock 90 Seconds After The Ignition Switch Is Turned "Off".
Default: Feature OFF; Program with the transmitter's LOCK button.
When this Feature is activated (turned ON), every time the ignition switch is turned "Off", the
doors will automatically lock 90 seconds later. You may open a door and exit the vehicle
without affecting this operation, and the LED Status Light will have no indication that the
automatic locking will occur.
2) The Doors Automatically Relock 90 Seconds After Unlocking By The Transmitter.
Default: Feature OFF; Program with the transmitter's UNLOCK button.
When this Feature is activated (turned ON), every time the transmitter is used to unlock the
doors", they will automatically relock 90 seconds later. Opening a door will not affect this
operation, although turning "On" the ignition switch will cancel the automatic relocking. The
LED Status Light will have no indication that the automatic relocking will occur.
3) The Starter Disable Will Automatically Engage 90 Seconds After The Ignition Switch Is
Turned "Off" And 90 Seconds After Unlocking By The Transmitter.
Default: Feature OFF; Program with the transmitter's OPTION button.
Continued Next Page
