IMPORTANT: For the first 48 hours after a transmitter is coded to operate the system, every
time the ignition switch is turned "on", the built-in piezo buzzer will beep rapidly for two seconds,
and the LED Status Light will flash for 90 seconds. If this occurs after the initial 48 hour period,
immediately reprogram your transmitters (See Page 10).
This Patented feature alerts you if someone has added an unauthorized transmitter to your system, and
is found only in Omega Research and Development products.
Page - 4
Concealed Transmitter Codes: Each Executive system includes two transmitters, and up to two
additional transmitters can be stored in the unit's memory for your convenience. Each transmitter has
its own unique code. Thus, no other transmitter is coded the same as yours. In fact, no one, including
the factory, can program another transmitter exactly like yours because the code is built inside the
transmitter's microprocessor and cannot be seen or copied.
Transmitter Code Jumping
TM
: Each time you press a transmitter button its signal will advance
to the next digital code in sequence. Each time the system receives the correct digitally encoded signal
from your transmitter, the receiver will then advance to the next digital code in sequence to match the
transmitter. Therefore, you can never transmit the same code twice, thereby preventing a code grabbing
device from operating your system.
Transmitter Battery Saver Feature: Many times transmitter batteries are prematurely exhausted
because the transmitter buttons are inadvertently pressed by objects while in a pocket or purse. The
Executive transmitter will turn itself "off" after a short period of continuous transmission, and thus
prevent drained transmitter batteries.
Transmitter Features
U N
L O C K
UNLOCK BUTTON
Pressing the transmitter
Unlock button will
unlock all of the doors.
Keyless Entry &
Security
Executive
On certain vehicles, pressing
the unlock button once unlocks
only the driver's door. Pressing
a second time will unlock all of
the doors.
OPTION BUTTON
Pressing the Option button for two seconds
can be used to activate remote trunk release
(vehicles equipped with power trunk
release) or other optional equipment, such
as Remote Car Starters.
Page - 5
Transmitter Functions
LOCK BUTTON
Pressing the transmitter
Lock butto
n
will lock
all of the doors.
L O C K
O
P
-
T I O N
GREEN LED LIGHT
Illuminates whenever any
transmitter button is pressed.
Instructions for programming up to 4 transmitters
to your Executive system are found on Page 10.
All Executive Keyless Entry and Security Sys-
tems can use the same Remote Transmitters. Your
system is capable of being operated by up to four
Executive transmitters, which are available from the
dealership where you purchased your system.
Your Executive system will
lock your doors upon turning the
ignition "On", and unlock them
when the ignition is turned "Off".
The E-2300
ATV
includes a Red LED Status Light* to inform you of the system's operational
condition. Your system features a Starter Disable circuit, the status of which is also reflected by the
Red LED Status Light. These are the conditions of the LED Status Light:
LED Off ...................................................................... Ignition switch is "On". Also, the system
is "at rest", indicating that no automatic
features (which may have been programmed
to operate) will occur.
LED On Solid Red ..................................................... System is in "Valet Mode".
LED Flashing Rapidly ................................................ Starter Disable has been programmed to
automatically engage.
LED Flashing Slowly ................................................. Starter Disable is engaged. This will occur
whenever the transmitter is used to lock the
doors. The Starter Disable may also be
programmed to operate automatically.
LED Flashes 1 To 4 Times After Ignition "On" ........ Number of transmitters stored in the system.
These four indicators are part of the Auto-
matic Transmitter Verification
TM
feature.
Page - 6
L E D Status Light
* LED is the abbreviation for Light Emitting Diode - which is defined in the Glossary.
The Easy Valet
TM
Switch is used to place the system into Valet Mode, which is used to stop or
interrupt any optional automatic functions, such as Starter Disable, which may be programmed to
operate. The Easy Valet
TM
Switch, in conjunction with your ignition key, also allows you to override
the system in the event of a lost or damaged transmitter, leaving the vehicle for servicing, washing, or
valet parking.
Easy Valet
TM
Mode: This feature allows you to activate the Valet Mode at any time by pressing
the Easy Valet Switch button for 2 seconds, unless the Starter Disable is engaged (this is indicated by
a slow flashing Red LED Status Light). Please note that once the Starter Disable is engaged, the ignition
switch must be turned "on" to enter the Valet Mode. When utilizing the Easy Valet
TM
Mode, upon
pressing the Easy Valet
TM
Switch, the Red LED Status Light will illuminate a steady, solid Red, and
the built-in piezo buzzer will beep once. While the system is in the Valet Mode, the Red LED Status
Light will remain solid Red (not flashing) at all times, and every time the ignition switch is turned "off",
the built-in buzzer will beep once as a reminder of this condition. To remove the system from Valet
Mode simply press the Easy Valet
TM
Switch at any time. The transmitter will operate normally while
the system is in Valet Mode, i.e., the doors will lock and unlock, the Option Button will still operate
- but the Starter Disable will not operate, and any programmed automatic functions are suspended.
Overriding The System: As mentioned in the previous section, once the Starter Disable is
engaged, the ignition key is required to allow the Easy Valet
TM
Switch to override the system and allow
starting the engine. To obtain a System Override, follow this procedure:
Easy Valet
TM
Switch
Page - 7
Continued Next Page
