The Status Light
The Status Light visually confirms the status of the system and provides
a high level of visual deterrence. Two colors are shown- Red for security
operations, and Green for remote starting operations. Combinations of both
colors are seen when the two operations are occurring together. The Status
Light is located in the vehicle interior, built into the window-mount antenna
module (see page 5).
Security System Status: The Red colored operations of the Status Light
indicate the status of the security system:
Page - 22
Automatic Transmitter Verification: For the first 10 seconds after the
vehicle’s ignition is turned on, the Status Light will flash Red a number of
times that equal the number of transmitters that are capable of operating the
system:
5) 1 Red Flash /pause = 1 transmitter is programmed.
Zone Violation: If the system enters an alarm condition, the Status Light will
stop flashing slow Red and begin to flash in sequence to indicate which
protected zone caused the alarm condition. The Status Light will flash and
pause to indicate which protected zone was violated while the system is still
armed, after it’s disarmed, and until the vehicle’s ignition is turned on. The
system’s Zone Violation feature’s memory can store two consecutive zone
violations. If there have been multiple violations, the Status Light will show
the two most recent violations in the order in which they occurred.
4) Flashing Fast Red = Last Door Arming or Automatic Rearming is in
progress, with the remote starter system off and in standby mode.
3) Flashing Slow Red = The security system is fully armed, with the remote
starter system off and in standby mode.
2) On Red Constant = The security system is in the Valet Mode, with the
remote starter system off and in standby mode.
1) Off = The security system is disarmed and not performing automatic
functions. The remote starter system is off, but in standby mode.
11) 4 Red Flashes / Pause = System was triggered by the sensor.
8) 4 Red Flashes /pause = 4 transmitters are programmed.
7) 3 Red Flashes /pause = 3 transmitters are programmed.
6) 2 Red Flashes /pause = 2 transmitters are programmed.
9) 2 Red Flashes / Pause = System was triggered by open hood or trunk.
10) 3 Red Flashes / Pause = System was triggered by an open door.
21) Slowly Alternates Red & Green = Full Valet Mode (page 20).
Remote Starting Diagnostics: Whenever the system is placed into Alarm
Valet Mode, the Status Light illuminates solid Red. However, when this first
occurs, the Status Light will flash Red, then 1 to 6 Green flashes before
resuming solid Red. This indicates why the engine stopped running from the
last previous remote starting.
15) Red / 1 Green Flash / Red = Programmed run time expired.
16) Red / 2 Green Flashes / Red = Brake was pressed or hood opened.
17) Red / 3 Green Flashes / Red = Engine stalled or bad tach signal.
18) Red / 4 Green Flashes / Red = Received transmitter command to stop.
19) Red / 5 Green Flashes / Red = Gear selector removed from “park”.
20) Red / 6 Green Flashes / Red = Security system triggered or low voltage.
13) Flashing Slow Green = The engine is running via the remote starting
system.
Starting System Status: The Status Light uses the color Green to indicate
the status of the remote starting part of the system:
Combination Indications: These indications occur when security and
remote starting operations are, or have been, simultaneous.
12) Off = The remote starter system is off and in standby mode. The security
system is disarmed and not performing automatic functions.
14) Flashing Fast Green = A remote start command has been received, and
the system is in the process of starting the engine.
26) Slowly Flashing Red 3 Times, Green 1 Time = The system is programmed
for manual transmission remote starting, and is
armed and ready for starting.
25) Slow Flashing Green w/ 1 to 4 Red Flashes = This indication is during
remote start operation after disarming the alarm,
and shows that the previously Armed alarm was
activated and reset prior to the remote starting.
The Red flashes are the Zone Violation (previous
page), occurring with the “engine running” indicator.
24) Rapidly Alternates Red & Green = Remote starter system engaged with
security system armed.
23) Solid Red w/ Green Flash = Remote starter system engaged with
security system in Valet Mode.
Page - 23
22) Solid Green w/ Red Flash = Security Armed with Starting Valet Mode.
