Other Controller and Transmitter Operations
The
2nd channel output
, which is operated by pressing and holding the
controller or transmitter “
II
” button for 1 second, is designed specifically to operate
your vehicle’s electric power trunk release. Your vehicle will respond by releasing
the trunk lid or rear hatch, chirping the siren twice, turning on your parking and
interior lights for 30 seconds, unlocking the doors, and disarming the system if it was
armed. The 2nd channel output will not operate when the ignition switch is "on"
unless the vehicle's door is open. If desired, the security system can be programmed
to remain armed when this feature is used, and connection of the 2nd channel may
require extra parts or installation.
To
Silently Arm or Disarm
the alarm, press and release the “
II
” button
twice. The siren’s confirmation chirps will not occur, and this operation simply
reverses, or “toggles” the armed and disarmed status of the system.
The
sensor
may be
temporarily bypassed
. When arming the alarm with
the controller or transmitter, within 3 seconds after the arming chirp press the “
II
”
button. The system will respond with another single chirp, confirming that the
sensor is bypassed.
The Excalibur also has a
3rd channel output
which is similar to the 2nd
channel, but it does have some special operational design differences. To operate
it, press and hold the controller or transmitter “arm/lock” and “disarm/unlock”
buttons together for 1 second. Or, a programmable feature allows the pressing of
the “
III
” button only to operate this output.
The differences are that 3rd channel output will operate regardless of the
ignition switch being "on" or "off", and there is no audible or visual confirmation.
Connection of the 3rd channel will vary, depending upon the chosen application,
and may require extra parts or installation.
There are also
optional 4th channel and 5th channel outputs
, which are
available if more remote control functions are desired. These outputs can be
repurposed from two other system outputs, the built-in door lock and unlock relays,
by Programmable Features #23 and #24. The system must be configured to utilize
these outputs; please consult your installer.
When these outputs are programmed and configured to operate, pressing the
transmitter or controller “arm/lock” and “
II
” buttons together will activate the 4th
channel output. Pressing the “disarm/unlock” and “
III
” buttons will activate the 5th
channel. Or, if desired, the controller or transmitter “
III
” button can be programmed
by to operate either of these channels.
Page - 13
Page - 24
The Programmable Features
It is important to note that programmable features affect the exact
operation of the system, and that the descriptions of any features
utilized should be used to supplement the basic system operations
which were described in previous sections of this booklet.
Each of the Programmable Features is described in detail in the pages
following the features’ list and programming instructions.
1
SecureCode
2
Last Door Arming
3
Automatic Rearming
4
Starter Interrupt Functions
5
Ignition Activated Override
6
Doors Lock With Ignition On
7
Doors Unlock With Ignition Off
8
Open Door Bypass To Previous Two Features
9
Confirmation Chirps
10
Confirmation Chirp Volume
11
Activated Alarm Cycle
12
Lights On Upon Disarm
13
Disarm Alarm Upon Trunk Release
14
Arming Delay
15
Steady Siren Output / Pulsed Horn
16
Alarm Functions Bypass
17
Ignition Activated Anti-Carjacking Protection
18
Door Activated Anti-Carjacking Protection
19
Remote Activated Anti-Carjacking Protection
20
Open Door Warning Upon Arming
21
III Button Operation
22
Doorlock Functions (an installation feature)
23
Factory Alarm Arm Output (an installation feature)
24
Factory Alarm Disarm Output (an installation feature)
The Excalibur AL-1500-EDP’s versatility is due to an incredible array of
programmable features. These are:
“
Features Programming Mode
” is the means for changing any of the features.
